You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
Though what if it still does not come off, after following the instructions in this book?
In my case the panel is stuck along the top edge and does not come off. What is the trick to getting it off along the top edge?
Pull out the ashtray and then the panel above and the cup holder . Radio will then come out
The 2004 Subaru Legacy OBD 2 port is under dash at left, next to kick panel"
im having the same problem...
Using a screw driver, remove the screws and the clips in the panel of the door and remove the panel gently. Remove any wiring connectors between the panel and the door, then remove the panel the rest of the way.
See that http://legacygt.com/forums/showthread.php/door-panel-removal-sound-deadening-install-pics-20069.html?s=d179c734a74474f2dd256fc3d607e56c&amp;
Well I have a 1998 Subaru Outback and i just figured out how to do it today. You will need a flat head screw driver and a Philips head screw driver. first you should remove the screw that connects the door handle and door lock. after that you need to pop out the rivets along the outside that connect the panel. be careful because if you don't get it where the rivet is located, you can distort the panel. they are spaced out approx 5-6 inches. also be careful to not tear the trim after that, you carefully take off the panel. you might need to slightly rotate it clockwise to take it completely off... and there ya go
Unfortunately, you have to remove the door panel cover. There are three or four screws and several pop-clips, but it is actually pretty simple. To remove the door panel, you have to disconnect the power connector and the speaker (just clips). Hope that helps
look on the drivers side kick panel
Has a starter relay in the engine bay fuse panel.
The turn signal relay for the 1993 Subaru Legacy is located behind the left hand instrument panel. Look on the left hand side of the steering column.
The fuel pump is located in the fuel tank on a 1993 Legacy. There should be an access panel inside of the vehicle to get to the pump.
Use a screw driver, remove the screws in the panel and remove the clips in the panel. Pull the panel out gently, remove any wire connections, and remove the panel completely.
Remove the driver of it in the the Control Panel-Devices And Printer-Right Click On the REMOVE DRIVER From iT Your Problem Is Solved
How do you remove the driver door panel on a 2002 Cadillac deville?
Using a screw driver, remove the screws and clips from the panel. Pull the panel away from the frame, remove the wiring connections, and the panel will come free.
Using a screw driver remove the screws from the door panel, remove the clips, and pull the panel away from the frame slowly. Remove any wiring connectors, and remove the panel the rest of the way.
No. To remove the widow its easiest to remove the outside panel
Using a screw driver, remove all of the screws in the door panel, and unclip any clips holding the door to the frame. Gently pull the panel away, remove any wire connectors, and pull the panel off the frame.
Use the right sized screw driver, remove the screws and clips from the panel of the car. Pull the panel from the frame, and remove the wiring connections, and the panel should come off.
it is in the fuse panel under the hood. Located on the drivers side.
It is located on drivers side panel under the dash. You have to remove the panel as well as the 2 screws that hold the fuse box to the side. Once you do this, you will find it up in the cavity. This is for my 96 Outack, it may be diff on your vehicle. J'
Using a screw driver, remove the screws and remove the clips from the door panel. Remove the panel slowly, remove any wire connections, and pull the panel off the door frame.
How do you remove the driver side door panel of a 1998 VW Beetle to replace the door handle cable?
Using a screw driver, remove the screws and clips from the door panel. Pull the panel away from the frame slowly, remove any wiring connections and the panel will come free.
Using a screw driver, remove all of the screws and the clips from the panel of the car. Pull the panel away gently, remove any wire connectors, and then pull the panel off the door.