Inside both of the front wheel wells are 3 small screws which run up the inside of the well...there are 2 small bolts at the bottom on the inside of the bumper in front of the tires (in which one has a guide bar attached to it)...then underneath, are 5 small bolts at the back edge...remove those and the bumper cover will slide out...there are rubber slides that fit into header panel slots holding it on...it will be snug so work it back and forth to loosen up...i just took mine off and put it back on fairly easliy...
how to install 2000 jeep grand cherockee Laredo front bumper cover
I do not believe there is a metal bumper. There is a foam insert that goes inside the bumper cover.
remove engine cover
Remove the screws in the wheel wells and underneath the plastic cover to remove the bumper cover. Then you can see to remove the actual bumper.
To replace a Pontiac Grand Am bumper cover, start by taking out either the three bolts on the side of the fender or in front of the wheels. Remove the top pushpins to remove the cover. Push back the two pins for each headlight, and pull them up. Unplug the lights. Then, get the replacement bumper, and snap it into place like the previous one.
how to change a valve cover gasket on a 97 mercury grand marquis ?
First remove the bumper cover. You need to take off the front grill to get at the plastic retainers that hold the top of the buimber on. There are about four retainers on the bootom of the bumper.
They are usually just inside the Front Bumper Cover. There should be wires attached. These are the ones that activate the Airbags.
On my 2000 grand cherokee, It was in front of the battery on the fender wall. Remove battery and you should find it. It is under the bumper cover, under the passenger head light. You either have to remove the front bumper, or you remove the headlight and cut an access hole.
REMOVE TWO TOP BOLTS ON HEADLAMP ASSY. THEN REMOVE BUMPER COVER, THATS RIGHT THE BUMPER COVER, THEN REMOVE TWO BOTTOM BOLTS
To remove the rear bumper cover on a 1993 Ford Taurus wagon, the lights need to be disconnected in the rear. Once all electrical connections are disconnected in the rear, remove the taillights and the fuel filler overflow hose. Remove any nuts and bolts holding the bumper cover on. Using needle nose pliers, pop the push pins around the bumper cover upwards. Slowly pull on the bumper to remove it.
Unbolt the front of the wheel well liner inside the wheel opening.Remove the bumper cover bolt from the bracket located inside of the bumper at the end.AT the front of the car, remove the bolts holding the bumper cover on, located underneath the vehicle.You should now be able to remove the bumper cover from the front of your Dodge Intrepid.An instructional video has been included to show you the removal process.
I would replace the bumper cover. They are very flexible and any attempt to repair will probably not last long. There are several places that sell aftermarket oem replacements for around $140
rip it off
# Apply parking brake,raise the vehicle and secure it # working under the vehicle,detach the fasteners securing the lower edges of the bumper cover # Working in the front wheel opening,detach the retaining screws securring the bumper cover to the inner fenderwell splash shield # Pry out the lower edge of the splash shield,then reach up behind the bumper cover and remove the bumper cover fender retaining nuts # remove the fasteners securing the upper portion of the bumper cover and pull the bumper cover assembly out and away from the vehicle. # Disconnect any electrical connections which would interfere with removal
To remove the rear bumper on the 2005 Nissan Sentra, you will first need to remove the rear bumper cover by using a flat tool to pry the pins. Then, access the bolts holding the bumper to the frame of the vehicle and remove the nuts. The bumper will then lift off.
1. If needed raise vehicle and support it on Jack stands 2. Remove the retaining screws in the wheel wells and along the upper and lower edges of the bumper cover. Remove the tail light housings. Remove the rear trim plate and pull luggage compartment trim out for access then remove the remaining bumper cover retaining screws. Remove the bumper bolts 3. On station wagons remove the rear window washer fluid reservoir for access to the bumper retaining bolts. The remaining bumper bolts are accessible from below 4. Pull the bumper and cover assembly out and away from the car
Remove the front bumper cover.... there should be 3 mounting bolts to remove the headlight after the bumper is removed.
I have a small dent need to remove it
To remove the front bumper from a Celebrity: 1. Raise the vehicle as needed and put on stands. The parking brake should be on. 2. Remove the end covers 3. Remove the valence cover. 4. Remove the nuts that hold the bumper to the mounting struts. Be careful to avoid having the bumper fall off onto you. 5. Remove the bumper. Reverse these instructions to put the bumper back on.
This video on YouTube (see Related Links) will show you how to remove the front bumper cover from of a 2004-2007 Honda Accord.
You will find the fuse box under a cover on the left side of the dash. Under the steering wheel are 2 screws that can be removed. Remove the cover and the box eill be visible.