0
How do you remove the front drivers side cv joint from a 1997 Olds bravada?
Wiki User
∙ 15y ago
unscrew it unscrew it unscrew it unscrew it
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you change a front drivers side u joint on a 1993 ford explorer?
How do u remove front axle u joints
How do you replace a lower ball joint on a bravada?
You will need to remove the tire and wheel from your Oldsmobile. Remove the retaining not on top of the ball joint. Pound the ball joint out. Reverse the process to install your new lower ball joint.
How do you change the CV joint on the front drivers side axle on a 1985 Chevrolet Celebrity?
Jack and secure vehicle. Remove tie rod nut and separate of knuckle. Remove axle nut and strut bolts. Use pry bar to remove inner CV joint from trans. Pull CV axle from vehicle.
How do you replace the front wheel bearings on a 1994 Saturn and what is the best way to remove it from the controller arm?
Remove u-joint clip (CV Joint), remove as an assembly, press bearing out.
Why would grease leak from the front drivers side cv joint on a Mazda 626 with manual trans?
The CV joint boot is bad, and needs to be replaced.
How do you remove front CV joint on Kubota rtv 900?
is there something holding front axel in trans case
How do you take apart a cv joint on a 1990 big bear ATV?
On the cv joint attached to the front differential, if you take off the boot, in front of the bearing, there is a cir clip. If you remove the cir clip the whole cv joint slides out of the differential. Have fun...
How do you replace the ball joints on 1997 E-350 Van?
From: http://en.allexperts.com/q/Ford-780/Ball-Joint-Replacement.htm Ball Joint Replacement [Ford Van] Remove the brake disc. Remove the wheel speed sensor. For additional information, refer to Section 206-09. Remove and discard the cotter pin and nut. Disconnect the tie-rod end. Remove and discard the cotter pin and the nut. Remove the pinch bolt adjuster. CAUTION: To prevent damage to the ball joint seal and the ball joint socket, do not use a pickle fork-type remover to loosen the ball joints. Remove the front wheel spindle. Strike the lower end of the front axle to loosen the ball joint. Remove the front wheel spindle. To install, reverse the removal procedure. Check and, if necessary, align the front end. Remove the wheel spindle assembly. For additional information, refer to Wheel Spindle - E150-E450 in this section. Position the front wheel spindle in a vise, and remove the snap ring from the lower ball joint. CAUTION: To avoid damage to the components, do not use heat to aid ball joint removal. Using the special tool and suitable receiver cup, remove the lower ball joint from the front wheel spindle. Using the special tool and suitable receiver cup, remove the upper ball joint. Installation CAUTION: To avoid damage to components, do not use heat to aid installation. NOTE: Clean the wheel knuckle ball joint bores. NOTE: The lower ball joint must be installed first. Using the special tool with suitable receiver cups, install the lower ball joint. Using the special tool with suitable receiver cups, install the upper ball joint. Install the snap ring in the groove at the bottom of the ball joint. Install the front wheel spindle.
How do you remove the large pin to remove the front wheel spindle on a Ford F-150?
If you mean the ball joint, there is a tool for that. http://www.sjdiscounttools.com/kdt2287.html
How do you replace a universal joint for a 1998 Oldsmobile bravada?
If you have to ask online, then step 1 is finding a qualified shop that can do it for you.
How do you replace the front universal joint on a 1994 dodge ram 1500 4X4?
Remove the rear U-Joint and be very careful not to loose caps or any needle bearings. Uses lock rings to hold it in place. Tape it together with duck tape. Now pull the drive shaft out of the transmission and remove the front U-Joint from the driveshaft and replace it. Reinstall in reverse order.
How do you remove front axle on a 1986 ford bronco II drivers side slid out passenger side wont come out?
Cut the metal ring type clamp off the rubber boot, then slide the axle from the slip joint...use standard hose clamp to reassemble
