Mazda 626

How do you remove the heater core from a 1995 Mazda 626 1 liter engine?

282930

Top Answer
User Avatar
Wiki User
2014-09-17 17:42:10
2014-09-17 17:42:10

You will need to drain the anti-freeze from your 1995 Mazda 626 cooling system. Remove the water lines from the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The heater core is located in the heater box which sits up against the firewall behind the dash board, you have to remove the dash to remove the heater box

User Avatar

The millenia P - has 2.5 liter engine, The Millenia S has a 2.3 liter engine

User Avatar

No , it is not an interference engine

User Avatar

The thrust bearings are inside the engine. You must remove crankshaft to replace them.

User Avatar

Yes, there is a 1.6 Mazda

User Avatar

Your 1998 Mazda 3.1 liter engine does not have timing marks on the crankshaft. The timing marks are on the engine flywheel.

User Avatar

Mazda named their truck models by engine size, so a B2300 is a 2.3 liter engine.

User Avatar

the engine can be either a: 1.6 liter 4 cylinder or 1.8 liter 4 cylinder

User Avatar

The amount of oil that goes into a Mazda 3 2.3 liter engine is 4.5 quarts. This would equal 4.3 liters.

User Avatar

The spark plug gap for a 1985 B2000 Mazda with a 2.0 liter engine is .8 mm. This is equal to .031 inches.

User Avatar

On a 1994 Mazda MX-6 : Both the 2.0 liter four cylinder engine and the 2.5 liter V6 engine have a timing BELT

User Avatar

The Kia 1.8 liter engine is a Mazda engine used in the Protege' from the mid-90s. That and the 2.0 liter engine used in 1994-2002 Sportages were used from Mazda and if the timing belt breaks, it will NOT damage the valves, thus a non-interference engine.

User Avatar

how do i find the timing marks for a mazda 6 2003 with a 2.3 litre engine

User Avatar

Remove the dash, its located under the glove box. Becarefull it will puke out antifreeze!

User Avatar

On the engine family .. LTK 3.0 T5 FCC1 there is no PVC valve on 1990 Mazda MPV

User Avatar

No. The 1994 and later Mazda B-series pickups are re-badged Ford Rangers. The 2.5 liter engine in them is an improved 2.3 liter engine that's been in Fords for many years. The Mazda B2200 uses a Mazda-designed engine that's fully different. Best bet is to go with a Mazda B2600i engine, or sell the pickup and buy something else. The i in B2600i stands for fuel injection, which increases power and gas mileage and reduces the amount of emission control equipment needed, simplifying the engine compartment.

User Avatar

You can find an exploded view of the 1996 Mazda Millenia 2.5 liter engine at most Mazda dealerships. You can also find the exploded view in most Mazda service manuals.

User Avatar

how do I remove a water pump on a 1990 4.5 liter cadillac engine

User Avatar

I cannot find any Mazda 2.7 liter that even uses a cam belt. Model year would really help to give you a 100% answer.

User Avatar

The 626 and the Millenia share the same 2.5 liter engine,the only difference being the version in the millenia makes more power.

User Avatar

on my 1997 Mazda 626, it's located on the left hand side bottom of the engine where the bottom radiator hose goes to the engine. hope this helps you.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.