answersLogoWhite

0


Best Answer
Copy

put a pry bar behind it (between it and the trans) and give it a sharp push, the axle is held in by a circlip, it will pop right out, and then right back in again, again, with a sharp push in.

User Avatar

Wiki User

โˆ™ 2011-11-10 23:24:03
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove the inboard cv joint on a 1988 Chevy Nova?
Write your answer...
Submit

Related Questions

How much is a universal joint for a 1988 Chevy siverodeo?

About $ 12.00


How do you replace a starter on a 1988 Chevy astro van?

Remove the positive cable from your 1988 Chevy Astro battery. Remove the cables from the front of your starter. Remove the starter retaining bolts. Reverse the process to install the new starter.


How do you remove the heater core in a 1988 Chevy G20?

Drain the water from your 1988 Chevy cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. The heater core will come out.


How do you remove the voltage regulator on a 1988 Chevy Caprice car?

yes


How do I remove the rear quarter panel window in a 1988 Chevy Beretta?

break it


What is the fuel capacity of a 17 foot 1988 inboard outboard?

20gals


What size Allen wrench to remove a caliper on a 1988 Chevy Nova?

3/8


How do you replace the thermostat located on a 1988 Chevy Cavalier 4 cylinder automatic?

Remove the water supply hose from your 1988 Chevy Cavalier thermostat housing. Remove the thermostat housing bolts. Lift the old thermostat out and drop in the new thermostat.


How do you change your fuel pump on your 1988 Chevy cavalier 4-cylinder .?

Remove the wiring harness from your 1988 Chevy Cavalier fuel pump. Remove the fuel lines from the fuel pump. Remove the fuel pump retaining bolts. Reverse the process to install the new fuel pump.


How do you remove the front rotors on 1988 Chevy Sprint?

First remove the right and left tires, and then proceed to remove the rotors. After you have replaced the rotors put them back on.


How to remove a Power Steering pump on a 1988 Chevy Celebrity?

Does your car have the 4 cylinder engine or the V6?


Where is the computer in a 1988 Chevy truck?

Remove the inside of the glove box and look in and down to the right and you will see it.


How do you remove evaporator core 1988 Chevy truck?

I have done this a few times, the best result was with a hell axe.


Replace thermostat on 1988 Corvette?

Drain the water from your 1988 Chevy Corvette cooling system. Remove the water supply hose from the top of your thermostat housing. Remove the thermostat housing bolts. Remove the thermostat. Reverse the process to install the new thermostat.


How do you replace starter on 1988 Chevy 1500 pickup?

Remove the positive battery cable from your 1988 Chevrolet 1500 pickup truck battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.


Will 1986 Chevy truck parts fit on a 1988?

NO. 1988 is when chevy changed everything.


How do you replace the starter on a 1988 Chevy pickup 8 cylinder?

Disconnect the - battery cable Raise and support the vehicle Remove wiring at the top of starter Remove mounting bolts Remove starter


How do you change a clutch slave cylinder on a 1988 Chevy S10 Pickup?

You will need to remove the transmission to replace the clutch slave.


Will a steering column from a 1988 Chevy truck work in a 1988 Chevy suburban?

Yes it will, samething


How to replace cv joints on 1988 Honda accord?

If the CV boot is torn open forget about re-booting the joint, buy a remanufactured axle and replace it. If the boot is starting to crack or separate but has not torn open to the point you can see the cv joint itself you can re-boot it. To replace the boot and/or halfshaft axle: First, remove the wheel cover and loosen the 36mm nut holding the joint to the bearing. Then raise the vehicle and remove the lower ball joint from the lower control arm and the knuckle. If your working on the passenger side, drain the transmission. Slide the half shaft out of the knuckle then use a prybar and pry the inboard end of the shaft out of the transmission or intermediate shaft, which ever should apply. Be careful not to damage the seal in the transmission. Installing the shaft is the reverse of removal. The inboard side of the shaft should snap right back into the intermediate shaft and transmission by means of a snap ring on the end of the shaft.


How do you Replace starter in 1988 Corvette?

You should begin by removing the positive cable from your 1988 Chevy Corvette battery. Remove the cables from the front of the starter. Remove the three starter retaining bolts. Reverse the process to install the new starter.


How do you change the fuel pump on a 1988 Chevy Celebrity?

you need to drop the gas tank down and remove fuel pump from tank.


IS A 1987 CHEVY TRUCK DOOR INTERCHANGEABLE WITH A 1988 K5 BLAZER?

Are the door interchangeable on an 1987 chevy truck and an chevy blazer 1988


What is the fuel pressure for a 1988 Chevy 5.3?

there were no 5.3 in production in 1988; but on a small block Chevy in 1988 you should have 22-25 psi


Vacuum diagram for 1988 Chevy Nova?

how do you hook up vacuum lines in a 1988 Chevy nova