answersLogoWhite
Toyota Camry
Bumpers

How do you remove the rear bumper on a 1996 Camry?

171819

Top Answer
User Avatar
Wiki User
2011-10-20 16:30:47
2011-10-20 16:30:47

I have a 94 Camry and it has the same body as the 96 model

There are approximately 22 nuts, bolts and screws to remove in order to remove the rear bumper. The locations are as follows. You will need a Phillips screw driver and a rachet with a 2 inch extension and 10mm/12mm sockets.

External1) One bolt Under each of the rear wheel arches.2) 2 Screws on each side underneath the bumper on the two sides (just behind the wheels)3) 1 Clip on each side underneath the bumper at the 2 edges. (I had to break these clips as I could not remove them)4) 1 screw type clip on the top side of the bumper, just below the tail light. (the screw needs to be turned and pryed up before the clip can be removed)

InternalThe back and side boot linings must be removed in order to have access to the nuts and bolts.1) 3 bolts on each side of the body (just behind the wheel arch) located at the top level of the body.2) Several nuts (approximately 8 nos. if I remember right) at the back panel of the body at the top level of the bumper. Theses can be identified as tapered edge of the bolt sticks out about 5mm beyond the edge of the nut).

Once all these are removed, remember to remove the licence plate light wire from the inside of the boot. My bumper came off when I pulled the it up several times, holding it from the bottom edge.

Hope this helped. Good luck.

Lalith.

1

Related Questions

User Avatar

how to remove 2013 passat rear bumper

User Avatar

Remove rear bumper on 99 ford tarrus

User Avatar

how do you remove and replace rear bumper on an xtype jag

User Avatar

To remove the rear bumper on the 2005 Nissan Sentra, you will first need to remove the rear bumper cover by using a flat tool to pry the pins. Then, access the bolts holding the bumper to the frame of the vehicle and remove the nuts. The bumper will then lift off.

User Avatar

Removing the Rear Bumper of a Passat...

User Avatar

The 1992 Mercedes-Benz 300 rear bumper is held in place with eight retaining bolts. You can remove the rear bumper by removing the retaining bolts.

User Avatar

The 1994 Ford Explorer rear bumper is held in place with eight retaining bolts. Remove the retaining bolts and the rear bumper will come off.

User Avatar

There should be 2 access plugs on each side in the trunk. Remove the bolts and slide the bumper out. Maybe a foot in from each side.

User Avatar

Usually such sensors are located in the rear bumper.

User Avatar

How do you remove seats in a 2007 Camry SE

User Avatar

Hi, I was looking for instructions as to "How to replace 1998 Toyota Camry rear bumper cover" and you got your question. If you have already replaced then please let me know otherwise I'm going to replace the part this weekened and I will let you know. Take care, Sam

User Avatar

300 dollars for each bumper 600 for both front and rear.

User Avatar

The rear bumper is held in place with eight retaining bolts. Remove the retaining bolts and the rear bumper will come off. Reverse the process to install your new rear bumper.

User Avatar

Drop it out of the back, there should be a hole above the bumper on the rear.

User Avatar

The bolts are in the rear of the trunk.

User Avatar

The 2007 Santa Fe rear bumper is held in place by eight retaining bolts. Remove the retaining bolts and the bumper will come off.

User Avatar

unsnap rubber pad on top of bumper and remove and go from there .

User Avatar

The rear bumper on a Honda Civic is held on using several mounting screws. After remove each screw the bumper will be held on with mounting clips. The bumper can be gently pulled off.

User Avatar

Have a crunched driver side rear corner bumper. Looking for tips how to remove the skin. Thanks Dorel

User Avatar

the sucker is welded on, you gotta remove the bumper and tail lights, and start drilling away at the welds

User Avatar

To remove the rear bumper cover on a 1993 Ford Taurus wagon, the lights need to be disconnected in the rear. Once all electrical connections are disconnected in the rear, remove the taillights and the fuel filler overflow hose. Remove any nuts and bolts holding the bumper cover on. Using needle nose pliers, pop the push pins around the bumper cover upwards. Slowly pull on the bumper to remove it.

User Avatar

if you have a warranty use it or you could go to a dealership or bodyshop

User Avatar

My Camry leaked around a vent in the rear guards it is behind the rear bumper and the carpet in boot covers - hope this helps

User Avatar

Just use the "force" to remove It.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.