0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you remove the jack box from a silverado?
after you remove the bolt, the spindle that holds the top on , must Be remove by turning it counterclockwise, it is threaded through, the floor
How do you take the rotor off of a Mitsubishi Montero Sport?
To access the rotor, remove the tire and brake caliper. There will be a cap protecting the bolt that holds the rotor onto the spindle. Removing the cap, located in the center of the rotor (on the spindle, not the rotor itself) will allow you to get access to the bolt. Removing that bolt frees the rotor from the spindle.
How do you change the front rotors on a 1996 Chrysler Sebring?
Step one is to remove the tire. Step two is to remove the brake caliper. Step three is to remove the cap that covers the spindle the rotor is spinning on. Step four is removing the bolt holding the rotor on the spindle. Step five is pulling the rotor off the spindle.
How do you change the front axle on a 1998 Honda civic?
jack up car remove wheel remove axle nut take bottom 19mm bolt loose and 14mm loose from horseshoe remove horseshoe separate spindle from lower ''a'' arm pull Axle out of spindle remove from trans to replace reverse process
How do you do a boot replacement on the rear axle of a 2001 Polaris Sportsman 400?
remove axle bolt from spindle and push it through you may have to remove spindle if no clearance. remove factory tie strap clean and grease before replacing with new boot reassemble in reverse watch for pin on nut threads reversed on passenger side always consult technical manual and follow safety protocols
How do you replace a rear wheel bearing on a 1995 Pontiac Bonneville?
remove the brake caliper and rotor then you will see three star head bolts remove those and the hole spindle will come out[you may have to persuade it with a hammer]then bolt on new one and your done
How do you remove the blades on a lawn chief 42 riding lawn mower?
Use a 9/16" Socket on a ratchet. There is one bolt in the center of the blade. Brace the blade with a block of wood to prevent movement. Loosen the bolt, remove the bolt and washers. Blade should come off easily now. Place your new blade in the spindle cradle and transfer the bolt and washers to it. Tighten with socket/wratchet. It's that easy! Unless, the bolt is stripped, in which case the mower deck will need to go to a machine shop to get the bolt out.
How do you change the hub assembly on a 1988 ford escort?
You will need to remove the spindle from the vehicle and use an arbor press to separate spindle from bearing and bearing from hub. There is also a snap ring (circlip) you will need to remove. Use the press to reassemble. If you do not have an arbor press, remove the spindle and bring to a machine shop for pressing.
How do you replace a hub bearing for a ford escort 1996 1.9 liter?
To replace the rear hub bearing you: 1. Jack up the wheel and support it with a stand. 2. Remove the brake drum and shoes. 3. Remove the cover on the spindle. 4. Raise the staked portion of the spindle nut with a hammer and punch. 5. Remove the nut. 6. Unbolt the strut from the spindle. 7. Unbolt the trailing link from the spindle. 8. Unbolt the lateral links from the spindle. 9. Take the spindle and bearing to a machine shop. The old bearing must be pressed out and the new bearing pressed into the spindle.
How do you change a front axle on a 2002 Pontiac grand prix?
Take the tire off remove the axle nut remove the pinch bolt and remove the ball joint from the spindle Push the end of the axle through the spindle"center of brake rotor" that might require a hammer and punch, be careful not to ruin threads carefully pry the axle from transmission, this may take some force while holding the axle and moving the rotor/spindle out of the way, pull the axle out reverse to install, making sure to properly torque all bolts and nuts to the recommended specs. failure to do so can result in an accident. Use thread lock on the ball joint pinch bolt for added safety.
How do you replace the oil filter spindle on a 1999 Ford Explorer?
After you take the oil filter off of the spindle look inside the spindle it will take an Allen wrench to remove it. Good luck
How do you replace front wheel bearing on 2007 Jeep Compass?
Remove the spindle from the car. You'll have to take off the axle nut, brake caliper, tie rod end, lower ball joint bolt, lower strut bolts and abs sensor to remove the spindle. Now you can take the spindle to a shop with the new bearing and have them install the bearing for you. Or you have access to a shop press you can do it yourself. Note: Shop presses can be dangerous! Press the wheel hub out of the spindle, then press the bearing out of the spindle. Pay close attention to the bearing you removed. (There is a magnetised side of the bearing and must be installed in the same way when putting the new bearing in. Magnet goes toward the sensor) Now reassemble the spindle in reverse order. That's the way I did it anyway. Good luck
