To replace a rear window regulator on 2005 CTS Cadillac remove the side protection panel of the car door then adjust the regulator.
To remove the drivers side window and regulator, you will need to remove the door panel from the door. Then you can unbolt the regulator and window to remove them.
Begin by removing the inside door panel. Remove the wiring harness from the electric window regulator. Remove the window regulator retaining screws.
Disconnect the battery.Remove the door panelRemove the power window motorRemove the regulator spring.Move the window down a bit and remove the two 10MM nuts from the window.Twist the window spring stud counter-clockwise.Now you should be able to remove the window regulator.
Remove the window regulator assembly from the door.Remove the motor from the regulator by drilling out the attaching rivets with a 3/16 in. drill bit.Connect the window motor to the regulator with 3/16 in. rivets.Install the window regulator assembly.
First you need to remove the door panel.Then remove the door handle bracket.Peel back the moisture shield.Tape the window into place,then unbolt the window from the regulator.Remove the window regulator from the access hole in the door.
To install a new window regulator on a MGRZ driver's door, remove the door panel and the wiring attached to the power window mechanism. Remove stereo speaker from the inside door and the window glass. Remove the old window regulator and replace with new.
1 open door 2 remove inner panel 3 lower window 4 take out window 5 remove (4) screws from regulator 6 take regulator of rails
It is best to replace entire regulator as one unit. Remove door panel. Remove bottom nut of regulator, and remove two top nuts of regulator. Loosen two bolts on bracket holding window. Support window, and carefully remove regulator as one unit.
remove your door panel there will be three screws holding it on. then you have to remove the screws holding your window to the regulator. then unbolt regulator and motor from door. Undo wiring going to motor.
How to remove the window motor from the regulator
Bad regulator maybe?
First remove the door panel.Then remove the moisture barrier.Next remove the window motor from the window regulator.
remove back seat, remove screws bottom and top of panel, remove panel. remove 3 bolts and motor arm, window and regulator will pull out.
You will have to replace the complete window regulator assembly.
you can
To remove the rear window regulator on a 1994 town car, remove the screws under the arm rest. Take off the rubber insulation and unplug the speaker wires to get it our of the way. Finally, remove the window regulator.Ê
The panel where the regulator is detachable. You will be able to remove it very easily. When you remove the panel you will see the way how the regulator can be replaced.
First, lower window approximately half way. This allows you access to the bolts that attach window to the regulator. Remove door panel. Using a 10mm wrench, remove the two bolts that hold window to the regulator. Then there are two upper and two lower bolts holding the regulator to the door. Then you remove the three bolts for the window motor which is toward the front of the door. You have to also disconnect the plug for the windo motor to remove the entire window regulator and motr that are all one unit. Replace the unit in the reverse way.
Take the door panel off,you will need to remove 3 bolts for the window motor and then 3bolts(maybe4) that hold the regulator to the window
You have to remove the door trim on the inside of the door. Also remove the window crank handle if it is manual windows. 1. remove the window regulator by unbolting the regulator from the door shell and sliding the window guide arms out of the window channels. 2. You then remove either side or both sides of the vertical window channel that the window goes up and down on. 3. Finally, most of the time you need to remove the window rubber seal that runs horizontally along the bottom of the window opening to get the glass and the regulator channel that is attached to the glass out of the door.
Remove the door panel. Remove the bolt that fastens the regulator to the window. Remove the 3 bolts that hold the regulator assembly to the door. Squeeze the entire assembly through the largest hole and replace with a new assembly in reverse order.
Have to remove the door panel screws, then remove speaker, drop the cables off the window motor (maybe), drill out the rivets that secure the regulator at bottom and remove two bolts at the top of regulator. push window all way up remove glass from regulator, I used a screwdriver but am sure there must be an easier way to remove the caulk that hold window to regulator. then dats about it..if you need to replace motor same thing drill out the rivets and pull out from right side of door...have fun that project sucked for me..LOL
To remove the window regulator in your 2005 Dodge Stratus, you would need to remove the door panel, and then the water shield behind the door panel. Tape the window into the up position with tape, and then you can access all of the nuts and bolts to remove the window regulator. I have included a link below to an instuctional video that will show you how to do this on a 01-06 Dodge Stratus.
Remove the door trim panel.Then clip the window regulator cables. Push window up and tape it in place until you can replace the regulator