0
Line up arrows and hash marks, then pull. It is held in place by a spring lock and should pull off with a little effort.
Wiki User
∙ 14y ago
Wiki User
∙ 13y agoYour manual is linked below and page 6 is where to look.
Add your answer:
Earn +20 pts
How do you install 065 cutter line on Weedeater model RTE 115 trimmer which you have only been able to find prewound spools at Lowe's?
Unscrew cap and remove. Remove line guide ring. Note which way to put line guide ring back on, slot to outer edge. Remove the empty spool. Don't take spool apart unless you need to get inside to remove string. The outer half should be yellow. Cut 25 ft. of .065 line. Start pushing the line inside the spool from the center making sure the string is winding inside in a counter clock direction which should be shown on the spool. Keep pushing until there is about only 6 in. left. Replace spool. Then the line guide ring, making sure to pull the string through the middle of it. Then hold the string on the slot in the ring while replacing the cap. You should be set to go.
How do you replace string on craftsman weedeater model 358.795550?
Unplug the weedeater from electrical source. Turn the weedeater upside down and remove the black knob on the bottom. If the black knob won't come off you can carefully use a large pipe wrench and turn it counter clockwise to loosen it. Be careful not to lose the slotted metal ring between the black knob and the trimmer spool. Remove the spool and clean it off. There is an arrow showing you where to insert the string. Start pushing the line into the spool going counter clock wise. Be sure to use only .065 ROUND string. Put the spool back on the spindle yellow side up. Hold the slotted metal ring with the slot facing up. Insert the string into the bottom of the ring and put the ring in the recessed circle on the spool, (yellow side). Pull the string over the slot and hold it there. Screw the black knob back onto the spindle, making sure the string is in the slot on the metal ring. Tighten the knob. You are now ready to go.
How do you fix a jammed weed wacker?
Stop motor. Remove line spool. pull spool from shaft and remove cord or weeds from around shaft. Replace spool on shaft. Re start motor.
What could cause a Weedeater trimmer spool to not spin if the motor runs and revs up nicely?
Take the spool off the the machine. By that I mean the part that contains the cutting line. There will be a spring that drives the spool. Get a pair of pliers and gently pull on it. If it comes out of the shaft it is probably broken or it came loose. If that does not solve the problem look at the spool where the nut is located make sure its there and that the housing is not wallowed out. If so buy a new spool.
How can you replace the trimmer line mac 2816?
Locate the trimmer head at the shaft. Remove debris in the head. Cut a 14-inch piece of the trimmer line and fold it. Place the spool against the spindle. Feed the ends of the line through the eyelets. Push the spool down and pull the trimmer line tight with your hands. Tighten the spool.
How do you replace the line on your closed face fishing reel?
First, remove the reel cover. Remove old line carefully, when you find the end, it should come off easily. Once the old line is removed, run the new through the cover, then tie the new line on the spool, and remember to remove the tag end as close as possible to the spool. Replace the cover, then reel the new line on the reel.
How do you replace the line on a spool with two lines coming out of the spool?
Cut two pieces of trimmer line about 6-8 ft long. Push the line into the opening in the spool until it comes out of the bottom of the spool. Place the end of the line into the small hole adjacent to the opening where the line came out of the spool. Pull the line tight while holding your finger on the line in the hole. Do this for both sides and then wind the spool in the reverse direction to fill the spool. Pull on the line occasionally to make sure the line is not binding up in the spool. There are spools that will take one single long line, where the center of the line is attached to a notch (or similar) in the center of the spool and then wound with one line on each side of the spool. Then, the end of each line is threaded through each hole in the trimmer head. It would be best if you consulted a user's manual. Try the following website for a downloadable manual for your application: managemylife.com or manualsonline,com
How to reload a stihl fs55 weedeater with new line?
ow do you reload a stihl weedeater need answer ASAP
Cant get the spool out of a craftsman line trimmer?
1. Rotate spool to line up arrows on spool and surrounding casing. 2. Find notch and pry with wide flat-end screwdriver. 3. Spool will pop out.
Echo weedeater primer bulb wont fill?
cracked gas line, cracked bulb, or weedeater out of gas
What is the procedure for re stinging the spool on a Weed Eater Model RTE113C?
Line the mark up with the arrow and pull real hard.
How do you get at the spool on Craftsman Model 358.799140 to replace line?
assuming it is not a bump head replacement and the unit still has the original head. 1)remove old line 2)bend replacement line strip into a upside down U shape with even sides 3)insert into hole in glide plate 4)pull the line to remove slack in middle of U as even as possible on both sides
