Headlights Tail and Brake Lights
GMC Envoy
Isuzu Rodeo

How do you replace a back bulb on a 2004 Isuzu Rodeo?

232425

Top Answer
User Avatar
Wiki User
2011-10-20 16:56:28
2011-10-20 16:56:28

I just did this a few weeks ago. First you have to take out all the screws holding the light fixture in. I suggest leaving the top screws in for last. The whole light assembly will come out when you do this. When you have the assmbly out, look for a couple of red plastic (lense) tabs on one side, and a couple of small screws on the other side of the assembly. Remove the small screws and then gently press on the tabs to release the lense. In most cases there is a foam gasket that makes the lense stick to the assmbley housing so you may need a little help getting the lense off. (I broke off one of the tabs by accident and used super glue to reattach it.) There is also a clear relector plate inside the lense that will probably fall out. It just slides into place so don't worry if it falls out. Once you have the lense off you can see the bulb in the assembly housing. Just push down and twist counter clock wise on the bulb and it should come out. Put in your new build and replace everything in revese order. \

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The EGR valve on a 95 Isuzu Rodeo is located on the back top of the engine. It resembles a cylinder.

User Avatar

the sensor is in the back of the rear differintial u need to check the wires running back by the right rear tire for breaks as this problem was apparent on my own 1993 rodeo other than that the sensor unplugs from the harness and is very easy to remove and replace

User Avatar

open the hood unplug the bulb from the back of the light assembly and un do the metal clip, pull bulb out of replace with a new one and reinstall

User Avatar

If its the bulb you have to unscrew the light cover and pull out the old bulb and put the new one in.Then screw the cover back on.

User Avatar

It is on the oil pan towards the back.

User Avatar

Please show picture of how to put on belt

User Avatar

lol! On my 1997 Rodeo (v6, 3.2l) it is in the back -- the manifold must be removed to access it. lol! On my 1997 Rodeo (v6, 3.2l) it is in the back -- the manifold must be removed to access it.

User Avatar

on the passenger side of the engine about midway back

User Avatar

The AC low pressure valve on a 1996 Isuzu Rodeo is located in the back of the engine compartment. The valve is on the larger of the two hoses that run from the evaporator to the compressor.

User Avatar

between the front wheels easy to take off and put back on but you do have to remove one screw from the heat shield to get it out it is very small cheaper to have overhauled than to replace.

User Avatar

It is really easy. First take off the tailgate and the glass lift hatch. Then you are done.

User Avatar

The bar that goes over them just pops off. Be sure to remove the back cargo light, first though. After you have snapped the bar off, you will see the speaker (4"). Just unscrew them with a regular size Phillips and do your replacement, then snap the body panel back on and put the cargo light back where it does. Voila! It took me about 30 minutes to replace both of my back speakers in my 99 rodeo last week.

User Avatar

You can find it about midways back under the vehicle, middle left hand side.

User Avatar

The egr valve is on the passenger side of the motor. It is a round canister at the back almost at the firewall.

User Avatar

It doesn't fold faward, you have to remove the bottom and undo a couple of bolts

User Avatar

It is located under intake manifold towards the back. It is above the starter.

User Avatar

Disconnect the battery, remove the spark plug cable and covers, and remove the old spark plugs. Put in the new plugs, put back the covers and cables, and reconnect the battery.

User Avatar

First pull the wiring connector from the back of the headlamp assembly. Then remove the gasket around the back of the headlamp out using the two pull tabs on the top and bottom. After that, you have to push down a thin metal clip to unhook the lamp. Once unhooked just replace the lamp and reassemble!

User Avatar

pull the battery terminals for like 5 min then out them back on start the car up should work

User Avatar

Mine has rear mount speakers in the back but off of the cargo area attached to the sides, just to the back sides of the back seat. It works and sounds perfectly.

User Avatar

It is on the oil pan towards the back at the bottom ( the lowest point of the oil pan)

User Avatar

1 2 3 4 5 6 cylinders are front to back and left to right 1,3,5, and 2,4,6.

User Avatar

If it won't come out try pushing up lighlty on the shitfer ( towards radio) or to the side towards drivers seat. You should here a click and the key will turn back If this enables you to get the key out you will need to replace the shifter.

User Avatar

It is on the left side of the engine above the exhaust pipe and not easy to get to. I suggest taking it to a garage/

User Avatar

BACKUP BULBS 1995 RODEOThere are 2 Philips screws, one on each side of the white coloured lens, on the rear of your Isuzu. Remove them and gently pry the lens off. The bulb is available at any automotive store and should be listed in your owner's manual.I replaced one of mine about 6 months ago.Yep...it's that simple! By the way I own 2 1995 Isuzu Rodeos. I would not trade either for anything new and North American! regardsgl347CANADA


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.