Auto Parts and Repairs
Car Computers and Sensors
VW Jetta
Crankshaft Sensors
1995-2005 Chevy Cavaliers

How do you replace a camshaft position sensor on a 90 Oldsmobile 98?

313233

Top Answer
User Avatar
Wiki User
2015-07-15 21:29:57
2015-07-15 21:29:57

It is pretty technical and special tools are needed. Take it to a garage.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

where is the camshaft position sensor located on a 1999 Oldsmobile intrigue

User Avatar

show location of camshaft position sensor for 2002 Oldsmobile bravada.

User Avatar

The Camshaft Position Sensor is located behind the Power Steering Pump.

User Avatar

In order to replace the camshaft position sensor, you would need to disconnect the electrical plug holding it in. Using a socket, hold down the bolt and remove the camshaft position sensor.

User Avatar

how do you replace the camshaft position sensor on a 1997 plymouth voyager 3l

User Avatar

how to remplace position of oxigen sensor

User Avatar

How do u replace the camshaft sensor for a 2000 Nissan xterra 3.3L and where is its locatoin

User Avatar

---------------------------------------------------------- The camshaft positioning sensor is hidden behind the starter motor on the 3.5 6-cyl. engine. I think it's the same for the 4.0. The starter motor must be removed to replace the sensor.

User Avatar

I changed only the camshaft position sensor on my 2000 Kia Sportage. So I don't think so.

User Avatar

do you need to take off the timing belt to replace a camshaft position sensor on a 2006 kia sorento

User Avatar

The camshaft position sensor is located near the thermostat housing. You should replace the crankshaft position sensor as well. This one is much harder to locate....it is on the backside of the engine that is between the firewall and the engine block. Both use the same sensor.

User Avatar

the camshaft position sensor is on the left side of the engine , at back on the upper side . you have to demont the conector , than unscrew and replace it

User Avatar

If I'm not mistaken, I think the camshaft position sensor on these engines is built into the distributor. You'd have to replace the whole thing.

User Avatar

It is located on the backside of the engine. Go to youtube and type in how to replace camshaft sensor on 2005 Nissan altima and it will show where it is and how to replace it, that is how I did my one.

User Avatar

Where is the camshaft position sensor on a 2005 Expedition?

User Avatar

The 1995 for Crown Victoria camshaft position sensor can be found on the back of the cylinder head. The camshaft position sensor will be labeled as such.

User Avatar

location of the camshaft sensor

User Avatar

in the distributor, you have to replace the whole unit.

User Avatar

Camshaft position sensor circuit malfunction.Camshaft position sensor circuit malfunction.

User Avatar

Yea, the crankshaft sensor is under the distributor and the camshaft sensor is inside the distributor, you cannot change it so you will have to replace the whole distributor.

User Avatar

CMP-camshaft position sensor CKP-crankshaft position sensor

User Avatar

The Pontiac 2.2 liter engine camshaft position sensor can be found on the back of each cylinder head. The camshaft position sensor should be labeled as such.

User Avatar

There isn't a camshaft position sensor. If you are asking because of an error code you received, it is caused by a signal that mimics the same signal as a camshaft position sensor.

User Avatar

The camshaft position sensor is located on the end of the camshaft housing, on a 2002 Daewoo. The sensor should be labeled as such.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.