0
The owner's manual shows that there are two screws on the top of the headlamp housing that hold the entire housing to the vehicle. Remove those two screws and then you have to slide the entire assembly out towards the front of the vehicle. This is the hard part as there is a clip that the bottom of the housing slides under that holds it down and you must slide the housing straight back to get it out. It's difficult because the housing is flush with the grill and body work so there isn't much room to grab. Just be patient and don't force anyting as it's all plastic. Once you've removed the assembly, unplug it from the vehicle wiring harness and then take the whole thing inside to work on. - Remove the rubber boot covering the lamp that needs replaced
- Remove the wiring connector
- Remove the metal retaining clip by turning counter clockwise... two small tabs on the clip slide under the two torx screws which holds the lamp in place.
- Replace old bulb with new one being careful NOT TO TOUCH THE GLASS PORTION OF THE BULB.
- Replace clip. This took the longest for me as I have big hands and had to do the whole thing using tools instead of reaching into the housing and doing it all by hand. You'll need a helper to level the housing while you work on the clip.
- Replace wiring connector. *** Test the lighting now before reassembling everything in case you have a bad bulb or connection. ***
- Replace rubber boot.
- Reconnect to vehicle wiring harness
- Slide housing straight back into vehicle, making sure the lower portion of the housing slides under the retainer in the bottom of the opening.
- Replace screws
Wiki User
∙ 16y ago
Wiki User
∙ 16y agoThis is how the instructions on my 98 jgc goes. There is a bulb that plugs into a socket dirctly behind the headlight. In order to access it you must lift the hood. Next, you will have to remove the plastic ring that holds the socket in the rear of the headlight housing. Twist the ring CCW (if you are facing the front of the vehicle)until it becomes loose and pull the socket and bulb through the hole. Then using a small flat tipped screwdriver lift out the little tab that holds the lightbulb on the socket and pull the bulb straight out from the socket. {Note: Pay Close Attention to the direction the plastic ring came out from, it is a pain to get back on if you don't. It will only go on one way...to hold the socket in place}
hope it helps you
Wiki User
∙ 12y ago2004 Chrysler Concord headlight bulb replacement: Purchase the correct replacement bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
Add your answer:
Earn +20 pts
What do you replace on a 2004 Chrysler Sebring LXi to prevent the digital display from flickering when your low beam headlights are on?
I think I answered my own question. My left headlight recently died, so when I replaced the headlight suddenly the problem went away. I'll post again if the problem returns.
Where is the headlight dimmer switch located on a 2004 Chevy Blazer S-10 and how do you replace it?
dimmer switch is on the turn signal lever, to replace you need to remove steering wheel
Where is the starter solenoid on a 2004 Chrysler Pacifica?
It is on the starter.
How do you replace the water pump on a 2004 Kia Rio 1.6L DOHC?
How do you replace the water pump on a 2004 Kia Rio 1.6L DOHC?
How much to replace alternator in 2004 Chevy Colorado?
Go found out
Where is the a tcm located on a 2004 chrysler concord?
The transmission control module is located on the drivers side just behind the headlight. you can tell it has a large wire harness there.
How do you replace headlight bulb on 2004 Mazda Tribute?
How do you replace headlight bulb on 2004 Mazda Tribute?
How do you replace a wheel bearing on a 2004 Chrysler concord?
Jack up the Concord. Remove the wheel. Unbolt the brake caliper and swing it out of the way. Remove the dust cover for the axle nut. Remove the nut and slide the hub off. Replace the bearings and reinstall.
How do you replace the headlight bulk on a 2004 Hyundai 2004 XG350L?
How do you change a headlight bulb on 1 2004 Hyundai XG 350?
Were is the cam sensor located on a 2004 2.7 Chrysler concord?
Front driver side of the engine.
How do you disconnect alarm 2004 Chrysler Concord?
The factory alarm is an integral part of the engine and body computers. It can not be disconnected.
How do you replace the headlight bulb in a 2004 Mitsubishi Diamante?
how to replace bulbs on a 2009 mitsubishi eclipse
How do you replace a daytime running light on a 2004 Suburban?
To replace the daytime running light on a 2004 Suburban, you will have to first remove the two metal pins that can be found on top of the headlight. The headlight assembly can be removed next. Pull out the plugs that are connected to the headlight assembly. Replace the bulbs and then reconnect the assembly.
How do you Replace passenger side headlight on a 2004 Chrysler Pacifica?
After removing the securing screws on top, you have to pull the headlight unit forward. You might have to flex the bumper fascia down a little to get a grip, as you'll need to pull assertively to disengage the retainer clip on the bottom of the unit.
What do you replace on a 2004 Chrysler Sebring LXi to prevent the digital display from flickering when your low beam headlights are on?
I think I answered my own question. My left headlight recently died, so when I replaced the headlight suddenly the problem went away. I'll post again if the problem returns.
Can you replace a 2000 landrover discovery headlight with a 2004 headlight?
No, the 2000 takes a 9003 bulb and the 2004 takes a 755 bulb. See sources and related links below.
How do you replace the headlight bulb located on a 2004 Chrysler Sebring Coupe?
2004 Chrysler Sebring headlight bulb replacement: Purchase the correct replacement headlight bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the headlight bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
