0
How do you replace a ignition lock cylinder 1995 Chevrolet. Corsica?
Wiki User
∙ 14y ago
You will need a steering wheel removal tool and lockplate compressor. 1st unhook battery then remove trim panel under steering colmn(if has anti theft key) unplugg steering colmn wiring connector with 7mm nut driver look for wire coated in orange that turns into 2 little white wires you will have to remove them from the turn signal switch plug Remove Airbag and unplugg carefully place it in safe place bag side up Remove steering wheel then you need snap ring pliers to remove the snapring holding in the clockspring pull it out a little and let it hang Attatch lock plate compressor and press lockplate down to remove the C clip holding it in place (this can be difficult I use an icepick to pop behind it to get it to stick out then take a flat screwdriver and work it around out of its groove got that Then remove the tork head bolts holding the turnsignal swith pull it out a little and let it hang now remove the lock retaing bolt and lock ( hook a wire at the bottom of the old wires for the lock so when you pull them through you have something to pull the new wires back through with. Its a Job if you never done it I recomend have a professional do it probably $125 labor cost
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you replace the ignition switch in a 1990 Chevrolet Corsica with tilt wheel?
The switch is on the steering column about 18 inches from the floor. Simply take 2 screws holding it on and replace it.The locck cylinder is under the steering wheel.
How do you change the ignition lock cylinder in a 2001 Chevrolet Tracker?
To change the ignition lock cylinder in a 2001 Chevrolet Tracker, first disarm the air bag system. Then remove the clock spring assembly to be able to remove the old ignition lock cylinder and replace with a new.
How do you replace an ignition switch in a 99 suburban?
how DO YOU REMOVE AN IGNITION CYLINDER FROM A MALIBU CHEVROLET 2000
How do i replace the ignition lock cylinder on 96 silverado?
Begin by removing the retaining ring at the top of your 1996 Chevrolet Silverado ignition lock cylinder. Slide the ignition lock out and remove the wiring harness. Reverse the process to install your new ignition lock cylinder.
How do you replace a 1996 Chevrolet Corsica?
Get a new car, i suggest a Malibu.
How do you replace ignition lock cylinder Isuzu rodeo?
How I can replace ignition switch cylinder from Isuzu Rodeo?.
How do you replace an ignition switch for a 1977 Chevrolet truck?
n ignition switch on a 1991 Chevrolet astro vanAnswern ignition switch on a 1991 Chevrolet astro van
How do you replace ignition switch for a 1994 Chevy Corsica?
Remove the retaining ring at the top of your 1994 Chevy Corsica ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.
How do you replace a melted tail light wire without removing the dashboard on a 93 Chevy corsica?
the wire is bare how do you replace the wire with out removing the dashboard on a 1993 Chevrolet corsica?
Can you replace the ignition lock cylinder on a 1994 Pontiac firebird without removing the steering wheel?
You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.
How do you replace 1981 Chevy ignition cylinder?
== ==
How do you replace the key cylinder ignition on a 1979 El Camino?
You will need to remove the retaining ring at the top of your 1979 Chevrolet El Camino ignition switch. The ignition switch will slide out. Remove the wiring harness. Reverse the process to install the new ignition switch.
