Headlights Tail and Brake Lights
Isuzu
Isuzu Rodeo
Turn Signals and Hazard Lights

How do you replace a rear light bulb in a Isuzu Rodeo?

717273

Top Answer
User Avatar
Wiki User
2006-05-05 18:04:57
2006-05-05 18:04:57

The complete assembly comes off by removing 4ea screws on the outside. Then remove the small plate on the rear of the assembly to get to the bulb.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

If its the bulb you have to unscrew the light cover and pull out the old bulb and put the new one in.Then screw the cover back on.

User Avatar

open the hood unplug the bulb from the back of the light assembly and un do the metal clip, pull bulb out of replace with a new one and reinstall

User Avatar

When you replace the brake light bulb on your Rodeo, be careful not to touch the bulb directly with your fingers - the oil from your skin will cause the area that you touched to burn hotter than the rest of the bulb, which causes the bulb to burn out quicker.If you are going to replace a bulb in your cluster, it is a good idea to replace all of them. Not only will the lights on your Rodeo be brighter, you decrease the likelihood you will need to change any of the bulbs again in the near future. A burnt out bulb in the taillight cluster of your Rodeo is an excuse for a police officer to pull you over. Check your bulbs frequently and change burnt bulbs promptly.

User Avatar

that depends on the model year of the rodeo. If its a 92/93/94 remove the guage housing module(see how do i remove the dash board of a 93 rodeo) Once the module is out the front and rear panels of it will pop off with a screwdriver and you can replace the bulbs.

User Avatar

2000 Isuzu Rodeo brake light bulb lamp replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb lamp replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

User Avatar

The bulb can be acessed behind the headlight in the center of the reflector,remove socket and pull out bulb and replace with new one.Do not touch bulb with fingers,oil from hands will shorten bulb life.

User Avatar

1989-2002 Isuzu Rodeo and/or Honda Passport brake light bulb lamp replacement procedure: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb lamp replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

User Avatar

First, make sure you get a DUAL filament bulb, if you get a mono filament it will not work properly. Open the tailgate, un screw the screws on each side of the tail light assembly. This is in one big unit. Then carefully take the stop light bulb out, you may have to pull a bit, they get really stuck in there. change the bulb with the dual filament. Carefully replace the whole assembly. Be sure that you the climate seal is on straight then replace the screws.

User Avatar

It is really simple. You simply open your hood reach in behind the headlight lamp, and twist the bulb out and unplug from the wire. Replace with new bulb and reverse the steps.

User Avatar

Pop Hood. Remove black retaining ring that holds light bulb socket in the light housing. This requires turning the ring and then pulling the socket out. Exchange bulbs and replace as removed. .

User Avatar

How do it replace the stop light bulb

User Avatar

open the hood, reach behind headlamp assembly, twist plug about 1/4 turn pull out bulb. reverse order to put the new one in, be careful not to touch bulb with your fingers.

User Avatar

You can replace the dome light bulb in a 2002 Chevy Cavalier by first prying the dome light cover off of the light. Then, remove the bulb and replace it by twisting the bulb from the socket.

User Avatar

how do you replace standing light bulb in the s430

User Avatar

Replace tail light on a 2001 Isuzu RodeoThere are 3 screws you need to loosen on a 2001 Isuzu Rodeo. There are two located along the side of the tail light inside the little black things that look like air vents. The other one is located between the bumper the tail light you may need a longer Phillips head screwdriver, preferably magnetic, for that screw. Once you remove all of the screws, slide the tail light straight back. It should pop back out of place. Try not to shake it out of place as to not harm the setting rods. If one or both of the plastic rods do break I don't believe will harm the vehicle or affect the operation of the tail light. Remove the corresponding bulb by turning the bracket counter clockwise and pulling the bulb out. The correct bulb number for a 2001 Isuzu Rodeo is the ever popular 1157. There are 4 screws to remove 2 in the side that are difficult to see 2 in the bottom that are very difficult to see behind the plateThere were only 3 screws to remove on my 2001 Isuzu Rodeo. The 2 on the side of the tail light and 1 on the bottom just above the rear bumper. After removing all 3 screws you have to pull the entire tail light straight out towards you. This may take some force because there's a plastic pin located at the top of the tail light to help hold it in place. Once you have the entire light out, turn the bracket counter clockwise as stated above. Gently push in the old bulb and turn it to unlock it from the socket then just put the new bulb in. Make sure that all lighting wires are tucked into the back of the light and then line up the plastic pins when you are snapping it back onto the vehicle. Put the 3 screws back in and you are good to go. :)

User Avatar

To replace fog light bulb of Monte Carlo you must remove the entire assembly. Replace the bulb that has been hindered and replace the assembly.

User Avatar

wjjeeps.com . they show how to replace every light and with what bulb

User Avatar

how do you replace the fog light bulb on a 2003 ford explorer.

User Avatar

how to replace brake light bulb fiat doblo van

User Avatar

how to replace map light bulb in a 2006 pontiac torrent

User Avatar

Hey There: What year of trooper do you have????

User Avatar

you don't replace the tail light you just replace the bulb in it

User Avatar

Repair the brakes. The light can be set on by a variety of problems from a burned out tail light bulb, to an unsafe condition such as stuck emergency brake shoes, or air in the lines, a bad sensor, or even the ABS module is bad.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.