0
Support car on jack stands. Remove rear cover, catch oil (no drain plug on stock cover) remove crosspin retaining bolt (1/2" wrench), pull cross pin out. Remove wheel/tire and brake drum. Push axle in then remove c-clip on inner end. Now the axle will slide out giving you acccess to seal/bearing.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you replace the rear wheel bearings on a 1967 Pontiac Firebird 400?
remove rear cover from differential, find 1/4 inch bolt in the third member that holds the 1 inch diameter pin between the axles. Remove the bolt and the pin, push the axle that you want to remove in towards the differential and remove the C-clip that keeps the axle in the differential. Pull the axle, using a bearing puller remove the oil seal and the bearing. Replace the bearing and the oil seal, make sure it is installed in the right direction or it will leak. install the axle, C-clip, pin, bolt, rear cover, and differential oil.
How do you replace an axle seal and bearing on a 1993 Ford Crown Victoria?
Assuming rear wheel drive and you're replacing the rear axle seal and bearing with drum brakes: With rear axle off the ground, on stands or blocks and parking brake OFF, remove tire/wheel. Pull brake drum, check for retaining plate that holds bearing, it's usually a 4 bolt square plate near the center of the axle. With the axle off, attach an axle shaft puller to the axle and slide the weight vigorously down the shaft until it pulls off. You will need to take the axle shaft to a shop that has a bearing press so that you can remove the old bearing and install the new one. Many auto parts retailers have a bearing press and won't charge to remove and replace a bearing from the shaft if you buy the parts from them.
How do you replace bearing and axle on 10 bolt seal?
Support car on jack stands. Remove rear cover, catch oil (no drain plug on stock cover) remove crosspin retaining bolt (1/2" wrench), pull cross pin out. Remove wheel/tire and brake drum. Push axle in then remove c-clip on inner end. Now the axle will slide out giving you acccess to seal/bearing.
You have a 99 Chevy Camaro and want to replace the right rear bearing does anyone know how to do this?
Remove the wheel and brakes. remove the differential cover. place vehicle in neutral. turn the driveshaft until you can see one 8 mm bolt that holds a shaft between the axles in place. Remove the bolt and the small shaft. push in on the axle where the rotor was then you should be able to see a c-clip on the axle inside the differential housing. Remove the clip(It just slides right out). now you should be able to just slide the axle right out. then just pry out the old axle seal and the bearing will be right behind it
How do you install alternator on 2001 impala?
Where is the mounting bolt on a 2001 Chevy impala so I can replace the bletAnswerWhere is the mounting bolt on a 2001 Chevy impala so I can replace the blet AnswerWhere is the mounting bolt on a 2001 Chevy impala so I can replace the blet
What are the torque specs for a vortec Chevy 350 two bolt main?
Main bearing torque on 98 Chevy 350 4 bolt main?? The main bearing caps should be torqued to 70 ft. lbs.
CV boot Ford Ranger how to replace?
A CV boot is found on the axle of a vehicle. To replace the outer boot remove the axle bolt and pull the boot off. The inner boot requires removal of the whole axle.
What is the size of bolt to a 2002 Chevy cavalier front axle?
axel hub nut is 30 mm
Will a Honda 250 big red rear end fit Honda 300?
No. They bolt up differently and have different bearing and seal kits. Also the axle is not as thick as a 300 axle.
How do you fix a ford F-150 4x4 rear wheel bearing?
access the rear differential, and remove cover.remove 5/16 bolt and remove pin holding axle in. with wheel and drum off, push axle in to reveal c-clip inside differential. once c-clip is removed, pull axle out of axle housing. remove axle seal with seal puller to access bearing. bearing must be removed using apropriate tools(bearing puller, slide hammer, etc..). install new bearing with bearing driver. install new seal with seal driver. reinstall remaining parts in reverse order.
What axles do a 1982 Chevy k20 4x4 have?
Front axle is a gm 10 bolt 8.5 with 8 lug spindels and rotors. Rear axle is a gm sf 14 bolt 9.5 with 8 lug drums.
How do you replace the rear shocks on a 2001 Chevy Venture?
They bolt in and out easily.
