Remove the 2 screws at the top of the instrument cluster bezel (or dress front cover), carefully pry out with a small screwdriver and set aside. Remove the 4 screws that hold the instrument cluster to the inner dash and pull out. Turn instrument cluster over to access the bulbs for removal and replacement. Twist the bulb retainer to remove.
How do you change the light bulbs in the instrument panel in 1998 Toyota corolla
If your 92 Toyota Corolla taillights are out, but the dash light and fuse work fine, the bulbs could have burn out. Replace bulbs on each side.
How you change fog lights bulbs on a 2004 Toyota Corolla
go inside the trunk there should be a clip you push that down an pull the assimbly out an replace the burned out bulbs hope this helps you...
When bulbs on a Toyota Corolla are working but one is not, it is usually a burnt out bulb. You can change this yourself.
First off are your dash lights out if so its more likely to be a fuse that you need to replace check your owners manual the dash lights in a corolla are LED lights so its not likely they have burned out. if your looking to change the color of the bulb go to an audio installer for directions on removing your dash panels to get at the bulbs to replace them there's one in your center section and i don't know about the instrument cluster
you don't! remove bezel for gauges, remove four screws for gauge assembly, pull forward and tilt, replace the four bulbs.
check the fuses
It is practically impossible to reach up behind the dash to change the bulbs. Remove the trim around the instrument panal and you should be able to pull it out enough to change the bulbs. You may have to disconnect the speedometer to get it out far enough.
To replace the rear bulb in a Toyota 4Runner remove the plastic covers located in the trunk. Taking off the plastic covers will reveal the taillight housing and bulbs. Replace the bulbs.
There are no individual bulbs, just LED's in the dials, and you will have to replace the entire instrument cluster.
You have to remove the instrument cluster to get access to the bulbs.
To change the dash light bulbs you must remove the instrument panel.
You don't state what they are or not doing. If none of them work, change the flasher. If just one side works replace the bulbs that are not working.how do you get at the bulb to change please explain
Remove the instrument cluster then replace the bulbs. = =
Do you still need an answer? yes
The instrument cluster must be removed to replace the light bulbs on it.
What model of Corolla ? You have to take the dash board out and the bulbs can be removed and replaced from the back. The dashboard on the Corolla is not that difficult to take out, but you have to do it slowly and carefully.
Step 1. Remove the two screws at the top of the outer panel that holds it in place. Step 2. Snap out the panel. Step 3. Remove the two screws that hold the cluster in place. The screws are located at both edges. Step 4. Carefully remove the cluster. Be careful not to damage the wire harness located at the back of the cluster. There should be about 3 or 4 bulbs in sockets that "lock" into place at the back of the cluster. Step 5. Remove the bulbs sockets by turning them counter-clockwise and removing them. Step 6. Remove the bulbs from the sockets. Take the bulbs to your auto store and get matching bulbs. Toyota also sells them for about $3.00 for a pack of 2. Reverse the above to replace. Good luck.
The instrument cluster needs to be removed to get at the bulbs.
check your owners manual the procedure is there as diy
probably because you need to get new light bulbs, go get that checked!! that's dangerous
U need a screw driver, open the trunk and at the latch there is a screw that holds the bulbs unscrew and replace the bulb, u might have to take the inside dash out but is easy to put back on
Low beams - 9006 bulbs or HB4 bulbs High beams - 9005 bulbs or HB3 bulbs
there are no fuses. take the dashboard cover off (the one over the speedometer) and replace the bulbs. be sure to use soap to remove the green bulb covers. make sure the ignition is off. dont break the plastic covers. use a long skinny screw driver phillips. a magnetic screw driver is better.