answersLogoWhite

0


Best Answer

To replace the remote oil filter lines on the 98 Jimmy 4 X 4 the old filters have to removed first by unscrewing the screws and the bolts. Once they have been been removed, the remote oil filters can be replaced.?æ

User Avatar

Wiki User

9y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you replace remote oil filter lines on a 98 jimmy 4x4?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace a fuel filter on an Infiniti qx4?

follow fuel lines to filter. remove lines from filter and fit lines to new filter.


How do you replace a fuel filter on the Infiniti G20?

separate the lines from the filter and fit the lines onto the new filter. just trace the fuel lines to find the filter


How do you replace the fuel filter on a Chevy Blazer?

Depending on the year, the blazers fuel filter is most likely on the frame. While covering the connection with a rag, loosen the fuel lines from the filter. Remove the filter and replace, then reconnect the lines.


How replace 2000 Jimmy 4x4 transmission cooler lines?

The transmission lines on a 2000 GMC Jimmy 4x4 are replaced by disconnecting the lines at the radiator and then the side of the transmission. They are then removed from the bottom of the vehicle and new lines put in place.


How do you replace the gas filter on a 1997 Chevy Safari?

its located under the drivers side loosen the lines on both sides you can move the lines enough to pull the filter out of the mounting replace the filter and check lines for leaks. a Chevy is an astro a gmc is a safari. and before you remove the fuel filter you have to de pressurize the system and then be prepared for spillage with some paper or towels. use eye protection.


How can you improve mileage on a 1990 Deville?

If you have not done so, replace the plugs, plug wires, air filter, and fuel filter. Also replace all under hood vacuum lines.


How do you replace the fuel filter located on a 1986 Buick LeSabre?

Just squeez the white colored plastic pieces and pull the lines away from the filter. Warning Fuell will leak or spray from lines but, will stop shortly. than just sanp the lines onto the new filter


How do you replace the fuel filter on a 1991 Mercury Sable?

You will need to jack up the RR corner of the vehicle to reach it. The fuel filter is fastened with a big clamp to the right side frame rail, close to the fuel tank, just ahead of the RR wheel. Use a small flat screwdriver to remove the two plastic clips from the lines attached to the filter. Be careful, the lines are under pressure, and there will be fuel that will spray out as you unplug the lines from the filter. Use a flat screwdriver to loosen the clamo from the body of the filter and then you can remove and replace the filter. Install the new plastic line clips that are in the box with the filter into the lines and then plug the lines onto the filter until you hear them click in place.


How do you fix an oil leak on the oil lines right by the oil filter on a Chevrolet?

It will depend on what kind of Chevy. You will have to replace the oil lines if they are leaking. you can either straight up replace, or take the lines to a place that works with hydraulics and get them to crimp on new hoses your lines.


How do you replace the fuel filter on a 1989 full size Blazer?

follow your fuel lines and find filter hold the fuel lines make sure to not break or crimp line and use a wrench to remove filter make sure there is no flames anywhere near cause there is gas in the filter


How do you replace a fuel filter in 1996 Buick Skylark?

Locate the fuel filter on the 1996 Skylark frame rail. While covering the fitting with a rag, loosen the fuel lines, and remove the filter. Take the filter off, and connect the lines to the new filter, keeping the flow arrow towards the front of the car.


How do you replace a fuel filter in a 87 5.8 ford crown Victoria?

raise the vehicle, locate the fuel filter back close to the fuel tank, remove the 2 plastic clips that hold the lines on, loosen the mounting clamp, and replace the filter.