answersLogoWhite

0


Best Answer
Copy

To get to the dash bulbs, you have to remove the side plastic panel in between the dash and the driver door. You can pry it off, but be gentle because it is only held together with plastic pop-rivets. You will not have to replace them, but you might break one or two (no problem). Then, you can remove the panel on the top of the dash and access the light bulbs behind the display. Don't be afraid, it all comes off with pressure. Just be careful. ---------------------------------------------------------------------------------------------- In the 1997 Mazda 626, all you have to do is unscrew the instrment frame, pop it out of the plastic rivets and remove it. After that, unscrew the instrument cluster (there are four screws, two on top and two on the bottom) unhook the three electrical outlets and pull the cluster out. It's quick and easy.

User Avatar

Wiki User

โˆ™ 2007-06-13 14:48:55
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the dash light bulbs in a 1999 Mazda 626 LX?
Write your answer...
Submit

Related Questions

How do you replace instrument panel light bulbs on 1999 ranger?

Do you still need an answer? yes


How do you replace the license plate light fuse for 1999 Mazda 626?

How do you change the liscence plate light fuse


How do you replace the thermostat located on a Mazda truck?

how do replace the thermostat on a 1999 mazda b2500 truck?


How do you replace rear lights on a 1999 Kia Sephia?

The taillights on a 1999 Kia Sephia are replaced through the cars trunk. Remove the plastic covers from the light housings and replace the bulbs.


How do you replace the front right turn signal bulb on a 1999 Mazda?

Without model of 1999 Mazda, its impossible to give detailed instructions. In general however, most owner's manuals will have instructions and illustrations for turn signal bulb replacement. Also, see sources and related links below for more information on the correct light bulbs.


How do you get to the rear brake light bulbs on a 1999 Nissan Frontier?

You have to unbolt the entire tail lamp assembly to change the bulbs. Unbolt the tail lamps from inside the corners of the bed, replace the light bulbs, bolt the tail lamps back in place.


How do you replace fuel injector on a 1999 Mazda 626 v6?

Where is the fuel injector located on a 1999 mazda 626v6


How do you replace light bulbs for radio on a 1999 Chevy Suburban?

http://www.corvetteradios.com/ sells the bulbs for the GM k1500 radios. They have a diagram showing how to solder them to the circuit board on their site.


How do you replace the starter on a 1999 Mazda Millenia?

i need a diagram to show me how to remove a starter on millenia s 1999 mazda


How do you open the tail light casing to replace bulbs in a 1999 Acura 3.2 TL?

You don't. REmove the bulbs by turning counterclockwise. From inside the trunk. There are trim panels that hide the sockets.


How do you replace the brake light on a 1999 Dodge Stratus?

Hey Laura==The whole tail light housing has to come off and the bulbs just come out from the rear. GoodluckJoe


How do you replace dashboard lamps on 1999 Saturn SC1?

Remove the instrument cluster then replace the bulbs. = =


How do you change brake light bulb on 1999 Honda Passport?

To change the brake light bulb on a 1999 Honda Passport find the light housing located in the trunk. Find the plastic covers for the lights and remove them. Pull the bulbs out carefully and replace them.


How do you change the brake light on a 1999 ford expedition?

Which ones? If it is the 3rd break light on top center of the vehicle. There are 3 Phillip screws take them out and replace bulbs and re-install... If it is the rear two break lights. Then open rear door hatch. There are 2 or 3 screws on the light housing remove them pull housing away from the vehicle. Replace light bulbs and replace housing to the vehicle.


How do you replace the thermostat located on a 1999 Mazda 626 V6 and show a diagrahm?

it is the same for all Mazda with a v6


How do you replace the front blinker light bulbs in a 1999 Lexus ES 300?

The bulbs go in from the rear. You may have to remove the light asy, by removing the top plastic rivet and sliding the whole assembly toward the front to disengage the three plastic assembly tabs.


If i replace the stop light switch on a 1999 Mazda 626 and the brake light still don't't work what is the problem problem?

try finding the fuse box and look for the brake light fuse on see if it is broken


How do you change a brake light on a 199 vw t4?

A brake light on a 1999 VW can be accessed through the rear of the vehicle. Locate and remove the plastic covers for the light housings. Remove the bulbs. Replace with new units.


What type of front turn signal bulbs go into a Mazda Protege specifically 1999-2003?

1157A


How do you replace the rear turn signal on a 1999 Acura Integra?

When replacing the rear turn signal on a 1999 Acura Integra open the trunk. Locate the rear turn signal housings and find the bulbs. Remove and replace the bulbs.


How do you replace the headlight bulb located on a 1999 Isuzu Amigo?

Pop Hood. Remove black retaining ring that holds light bulb socket in the light housing. This requires turning the ring and then pulling the socket out. Exchange bulbs and replace as removed. .


How do you replace the rear turn signal and brake light bulbs on a 1999 Pontiac grand prix after you pull the lining of the trunk away from the back of the trunk?

3 big plastic wing nuts hold the tail light assembly in the body. remove those and the tail light can be removed to gain access to the bulbs.


How do you change 1999 Acura TL headlight?

To change a headlight on a 1999 Acura TL open the hood and locate the bulbs which are plugged into the housings. Loosen the bulbs and pull them off. Replace them.


How do you replace the tail light in a 1999 GS 300?

I figured out the answer to the question I asked. You need to remove the tail light in order to get at the bulbs to replace. To remove the light, there are 4 screws that you need to take out- two on the outside and two on the inside behind the carpet. Its actually quite easy once you figure it out. Thanks.


How do you replace the license plate lights on a 1999 Mazda protege?

Open the trunk. Turn the socket counterclockwise and remove. Then gently pull out the light bulb. Place the new bulb in the socket and replace the socket into the lens by turning clockwise. Replacement light bulb #3652.