Want this question answered?
hi there you have to take all the spline key srews out at window switches and bottom of door and down side panel and take wire for door open button
It will not take long at all to remove door trim from a Renault Menage. All you have to do is remove the bottom 10 mm bolts on the door, un-clip the door lights, undo the plastic trimming from the clips, unscrew the door cover and then remove all trimming.
the paint colour code will be on a paper label stuck to the body of the car somewhere on my megane scenic it is stuck on the lock side of the door pilar at the base.be carefull which number you use it will also have the interior trim listed as a code on the same label and it doesn't say which is which.
This is a right bugger of a job. You need to have the trim off and for that you need the door open. And to open the door you need to have the trim off. I got a replacement door trim at a breakers before starting the job. I then cut away the old trim very carefully with shears and eventually got into the mechanism. A tiny clip had come undone. I repaired it by binding with fine copper wire and then fitted the replacement trim. That was three years ago.
Remove the screws from the bottom of the trim and the one from inside the handle. The trip is mostly clipped onto the door and also has some foam stuck around the side as a seal
open the door, remove door trim and the torque screw holding the strap to body, and two nuts holding strap to door and remove door stop from inside door
the paint colour code will be on a paper label stuck to the body of the car somewhere on my megane scenic it is stuck on the lock side of the door pilar at the base.be carefull which number you use it will also have the interior trim listed as a code on the same label and it doesn't say which is which.
It is in the door. I suggest you take it to a trim shop to have it replaced.
AnswerFRONT DOOR TRIM PANEL REMOVALRoll door glass down.If equipped, remove window crank Window CrankDisengage clips holding speaker grille to trim panel Front Door Trim PanelRemove screws holding door trim panel to door from around speaker opening.Remove screw cap from bottom of arm rest pull cup.Remove screw holding arm rest pull cup to support bracket behind trim panel.Remove screw cap from behind inside door latch handle.Remove screw holding door latch handle to door panel.Disengage clips holding trim panel to perimeter of door.Lift trim panel upward to disengage upper retainer channel.Tilt top of trim panel away from door.Disengage clip holding latch linkage to back of release handle Linkage ClipSeparate door trim panel from vehicle.INSTALLATIONPosition door trim panel next to door.Engage clip holding latch linkage to back of release handle.Position door trim panel on vehicle.Engage trim panel to upper retainer channel.Engage clips holding trim panel to perimeter of door.Install screw holding door latch handle to door panel.Install screw cap from behind inside door handle.Install screw holding arm rest pull cup to support bracket behind trim panel.Install screw cap from bottom of arm rest pull cup.Install screws holding door trim panel to door from around speaker opening.Engage clips holding speaker grille to trim panel.Install window crank handle, if so equipped.
take screws out and pull door trim off
remove the inside trim or cut a hole to reach the mechanism and replace the inside trim.
To replace the door lock sensor you have to replace the door lock unit. You have to remove the door inside trim panel. To remove this trim panel carefully prise the top of the inside door handle ( use a plastic priser, a metal screwdriver may csratch). Remove torque screw inside handle. Next there is a plastic sign on the door trim panel that says "SRS air bag" Using your plastic priser prise it from the bottom. It should open like a trap door, inside there is another torque screw remove it. Carefully prise the trim panel from the door it is held on with plastic push on holders and a waterproof sealant. You should now be able to see the door lock Remove the door lock screws and unclip wires. To extract the lock from the door you have to remove the two revits holding the window sliding bar Carefully sneek the lock down and out through the opening at the bottom of the door. Reverse the process for fitting.