answersLogoWhite
Starters and Ignition Systems
Chevy Corsica
Chevy Blazer S-10
Ford Bronco II

How do you replace the ignition cylinder in a 1991 Chevy Corsica?

383940

Top Answer
User Avatar
Wiki User
2015-07-15 19:33:40
2015-07-15 19:33:40

Not an easy job requiring special pullers and tools. I suggest taking it to a garage.

1

Related Questions

User Avatar

Remove the retaining ring at the top of your 1994 Chevy Corsica ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.

User Avatar

how do you replace ignition switch on a 1992 Chevy cavalier 2.2 4 cylinder

User Avatar

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.

User Avatar

remove the two nuts holding the master cylinder on the power brake booster

User Avatar

Go to autozone.com they have this information on their website.

User Avatar

Where is the Water Pump located and how do you replace it on a 1990 Chevy Corsica?

User Avatar

I broke my key in the ignition and cant get it out. My only option I can see, is to replace to tumbler. How do I remove it?

User Avatar

The 1992 Chevrolet Corsica ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.

User Avatar

A Haynes or chiltons manual has the how to. Or do a search for a forum for Chevy corsica specific

User Avatar

how to replace an ignition switch for 2005 chevy equinox

User Avatar

It will take an experience mechanic approximately 8 hours to replace the timing belt in your 1992 Chevy Corsica. The 1992 Chevy Corsica does not have each timing chain, it has a timing belt.

User Avatar

can I switch ignition cylinder with a different ignition cylinder w/key in a 2004 chevy Malibu without having to use a passcode

User Avatar

You need electronic equipment and know how to to diagnoise the ignition system of the new cars.

User Avatar

To replace an ignition switch on a 2000 Chevy Blazer remove the lower steering column and dash. Locate the ignition switch and pull the end-clip off the main harness. Remove the mounting screws from the ignition cylinder and replace the unit.

User Avatar

cost to replace heater core 1994 corsica

User Avatar

It is in the fuel tank.. You should obtain a HAYNES manual for this job. NAPA stores.

User Avatar

i need the bracket that the ignition cylinder slides into.... the piece that mounts to the stering column

User Avatar

1 for each cylinder a 6 cylinder has 6 a 4 cylinder has 4 and so on.

User Avatar

With no key you will have to drill out the existing tumbler assembly from the switch in order to unscrew the ignition switch bezel.

User Avatar

According to the Chilton Corsica/Beretta 1988-1996 Manual, there are 21 steps to removing the ignition cylinder (and another 15 - 20 to reinstall it). Not that I don't want to past them all here, but you should get a manual... they're handy to have for any repairs.

User Avatar

The side view mirror on a 1995 Chevy Corsica is mounted by screws. Remove the screws and panel for the mirror on the inside of the vehicle. Pull and replace the unit.

User Avatar

located in the fuel tank of a 1992 corsica ,it may be the same for your model if this is so you may need to drop the tank . I would notadvice you to take on this job unless you have to.

User Avatar

on the drivers side just under the exhaust manifold


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.