0
Disconnect the battery. Remove the steering wheel. Remove turn signal switch,Remove the buzzer switch with needle nose pliers. Then insert the key(make sure it is not in place beforehand) and place in lock position. remove lock cylinder retaining torx screw. Then with key in place, pull out the assembly straight out.Disconnect the electrical connector from the bulkhead connectorand remove retaining clip. attach some wire to the connector to help with installation and pull harness through column. Installation is reverse.
Wiki User
∙ 17y ago
Wiki User
∙ 14y agoCaution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder
Wiki User
∙ 10y agoif you mean the ignition lock cylinder in the steering column you need a special depressing tool to remove a lock ring inside the column after steering wheel removal,remove the depressing tool,remove three screws that hold the turn signal cam pull that towards you and there is a 5-16 headed screw you take out next and the lock cylinder will come straight out ,put the new one back in . installation is the reverse of removal. but if you mean the actual ignition switch you have to remove an interior colored plate(2 bolts usually)right there under the steering column then remove two 15 mm nuts the column should drop down enough for you to unplug old switch and replace with the new on you got to be sure that switch is in the right position for the rod alignment adjust switch as necessary by two 5-16' screws and your done .replacement is opposite of removal process also make sure to remove the string for your gear indicator before you drop the column or you 'will' break it.
Wiki User
∙ 8y agoIGNITION ? ARE we talking ignition coil-ignition wires ignition switch-key & tumbler.
Wiki User
∙ 8y agoNot an easy job requiring special pullers and tools. I suggest taking it to a garage.
Wiki User
∙ 15y agoIf it is on the steering column you have to remove the steering wheel, lock ring and turn signal plate to access the ignition lock bolt. There are a couple of tools needed to do this. work.
Add your answer:
Earn +20 pts
How do you replace the ignition distributor on a 93 mx6 v6?
How do you replace the ignition distributor on a 93 mx6 v6 pics?
On a 93 Chevy cavalier- do you have to pull steering wheel to replace ignition switch?
yes
How do you replace an ignition switch 93 Buick roadmaster?
fuel pump keeps running after the key is out what do I need to check I have to remove the fuses to stop the pump.
Where is the ignition control module on 93 olds cutlass cierra s with 3300 V-6?
The ignition module on a 86 ciara 2.5 is located under hood, center,lower engine area,below driver side of intake manifold . mounted inside of distributor
Why wont your 93 dodge stealth start turns over no start and it does not have a crank cencor do you need this?
If the 93 Stealth came with a crank sensor but it does not have one now, then it will not start. The sensor shows the ignition coil when to send power to the spark plugs.
What is the towing capacity of the 1993 suburban?
10000LB on the 93 GMC Suburban 2500 with the 5.7L Engine
How do you replace the ignition distributor on a 93 mx6 v6?
How do you replace the ignition distributor on a 93 mx6 v6 pics?
Where is the ignition signal disconnect on a 93 suburban?
On the firewall under a black plastic cover that has two plastic black nuts
On a 93 Chevy cavalier- do you have to pull steering wheel to replace ignition switch?
yes
1999 gmc suburban intermittently bogs down when accelerating and then stalls but will restart when cool?
it is possible that it is the ignition coil but im not sure, that's what happened to my 93 1500 silverado and the coil was the problem. it might be an idea to check it but im not sure on newer gm models
Why does the taillight on a gmc 93 sonoma keep shorting out when bulb is replaced?
You need to replace the whole assembly. go to amazon.com and look up something like this: 93 gmc Tail Light Circuit Board
Can you put a 89 suburban trans in a 93 suburban?
NO.You can only use a 93 or 94 only
How do you replace the ignition switch on a 93 2500 Chevy?
You switch the carborator with the ac and then rewire the inside to the dashboard
How do you replace the ignition cylinder for a 93 Saturn when the empty tumbler is Stuck in the on position?
Sorry You can't you will have to replace the whole housing If the cylinder doesn't turn Your out of luck
What is the cost to replace an ignition module in a 93 Chevy Lumina?
All together depending on where you go parts and labor about 722.00 : - )
How do you change ignition switch on a 93 Honda Accord?
how to change manual ignition switch on a 93 Honda accord
What 93 GMC Sonoma parts are interchangeable with the 89 GMC s-15?
Yes
