0
How do you replace the lower timing belt pulley bearing on a Ferrari 308 GTS?
Wiki User
∙ 14y ago
Put the car on a lift, drop the motor/transaxle out of the car on an engine stand and break down the engine. You will need to separate the engine from the transaxle at this point.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where are the timing marks for a vauxhall Astra 1.6 8 valve s reg?
The timing marks, on your 1.6 liter engine, can be found on the front of the main pulley. The timing marks will be scattered around the outside of the pulley.
What are the sensors on a Ford escort ZX2?
The Crankshaft Position Sensor senses it's position from a toothed timing ring behind the Crankshaft pulley. The CKP is above and to the left of the crankshaft pulley.
What are the timing marks for a 1988 Audi 80?
I depends on engine you have in your car. All timing marks are located on the crankcase pulley, cam pulley and, distributor has timing marks as well. In order to view all timing marks, be sure to have the front bumper removed & timing belt covers removed. In order to turn the crankcase by hand. Have a bottle of whiteout ready to place on timing marks for easy refferance. Always crank your wrench clockwise during timing mark lineup, remove sparkplugs to lose the engines compression. Whatever you do, do not remove the timg belt until you have all refferance marks lined up. At the crankcase, you will notice a permant refferance marker, ture the crankcase until you see a small notch on front of the pully. Once you find it, view the timing marks for the cam pulley. if the notch mark on the pulley don't line up with it's own refferance marker, turn the crankcase till these marks line up together. If they line-up, remove the distributor cap from the distributor and check to see if the rotor button lines-up with the number 1 notch on the car's distributor. If so, it's time to replace the water pump, crankcase seals, camshaft seals and install a new thermostat. Be sure all the pulley are locked into place to keep from moving when installing the new timing belt. To save yourself any headaches, buy a factory manual that has all the torque specs when replacing everything.
What special tools are needed to replace a timing belt on a 2000 ford escort ZX2?
camshaft timing peg and a crankshaft alignment tool... I'm half way through doing mine and realizing you need to take the camshaft pulley off to get to the bottom gear for the timing belt, I'm still stuck on how to get it off, it says to use a strap wrench so I'm guessing for to hold the pulley while you remove the bolt... anyone ever acomplished this?
How do you replace the water pump on a 2004 olds Alero 3.4L?
Pay about $600.00 or get the book. You have to remove crank shaft pulley, timing chain cover, very hard job. You do not need to remove the crankshaft pulley to replace the water pump on a 3.4L v6. If one wanted to remove the water pump housing/timing chain cover on this engine, then yes removal of the crankshaft pulley would be needed. Maybe you are confusing this 3.4L with the 2.4L where as the water pump is driven by the timing chain. This kind of repair at the mechanic wouldn't cost more than $100. It is a very easy job and the water pumps for these engines range from $10 - $30. It took me only 30 minutes to replace my water pump, and I'm only a hobbyist. I only paid $13.99 for my water pump. I drive a 2001 Oldsmobile Alero 3.4L 3400 v6
Where is the crank shaft bearing located?
It's behind the timing belt cover on top of the crank pulley.
How do you replace the water pump on a 1989 Nissan Stanza?
ca20? remove all the belts, water pump pulley, underdrive pulley, timing chain cover and timing belt and the water pump is accessible. I would replace the timing belt too.
Does timing belt tensioner needs to be replaced along with timing belt on a 2001 Isuzu rodeo?
Not unless the bearing in that pulley is noisy or rough when you spin it.
How do you replace a timing chain for a 2003 Chevy cavalier?
In order to replace a timing chain for a 2003 Chevy Cavalier, a person will need remove the oil pan, crankshaft pulley and hub, timing cover bolts, and timing cover. Then the timing cover gasket, timing cover and bolts, crankshaft pulley, and oil pan will need to be installed.
What causes the 1998 Vanden Plas to make a rumbling or diesel sounding noise at idle whlile in gear?
front of timing pulley making rumbling noise took belt off and still making the same noise.is the timing chain are is it a bearing on pulley.
Why is a timing belt like a belt and pulley?
It is not like a belt and pulley. A timing belt is a belt and it fits on a pulley.
When you change the water pump pulley do you have to reset the timing belt?
If the timing belt drives the water pump you should replace the belt at the same time as the pump.
How do you change a timing chain on a 98 astro van?
Requires removal of: Fan shroud, serpentine belt, fan, water pump, timing cover, crank pulley(s). Requires crank pulley puller/installer tools. Requires timing gear puller to remove crank gear. Replace chain and gears together. Replace with all-metal gears, not composite sets. On this vehicle it is recommended to replace the timing cover each time it is removed.
How do you replace the thermostat located on a 1992 Pontiac Le Mans?
You have to remove the timing belt cover,camshaft pulley and timing belt.Itis near the top behind the belt.
How do you replace timing tension pulley on 1994 escorts?
You'll have to remove the timing cover which means the motor mount on that side has to come off and the engine weight supported by a block under the pan of the engine. The serpentine belt has to come off first. Then the timing cover. Then the crankshaft pulley. Then the timing belt has to come off. Last thing to do is take the tensioner pulley off last. The new pulley and a new belt will have to have the timing of the valves set correctly. This is beyond the scope of a DIYer. Get a mechanic to do this for you. If the valve timing isn't perfect, the engine will not have any power.
How much to fix the timing belt on 92 GEO tracker?
When you replace the timing belt you should replace the water pump and tensioner pulley as well. It may save you in labor costs down the road. But, all together it is about $500.
How do you replace the water pump on a 2000 Mazda Millenia?
In order to remove the water pump on a 2000 Mazda Millennia, you must first remove the timing belt and the pulley for the water pump. Remove the pump itself by detaching the four bolts that are securing it. Next, replace any gaskets, install the new pump, then the pulley, and then the timing belt.
