0
How do you replace the transmission pulley on a John Deere STX38 yellow deck?
Wiki User
∙ 13y ago
I'm currently replacing my transmission pully in my yellow deck JOHN DEERe STX38. You can not get to it from under the seat. As far as I can see the only way is to drop the transaxle.
Vince
Wiki User
∙ 13y agoYou should be able to remove the battery and the battery tray from under the seat and get right to the transmission pulley. Just remove the nut from the shaft and it should slip right off.
Add your answer:
Earn +20 pts
Is the John Deere 8345r a manual transmission?
The John Deere 8345r has an ivt transmission.
What is the belt size on a john deere 214 from the engine to the transmission?
The belt that runs from the variable speed pulley back to the transmission is part number is m44121. it is 67 3/8 long and 5/8 width.
What color is the deere in the John Deere logo?
Yellow
The illustration on the drive belt routing on your john deere gt225?
i need diagram on how to replace deck belt on John Deere GT235 mower
Where can I find a diagram on how to replace the transmission belt on a John Deere 112L garden tractor?
At Lowe's or Home Depot. Fa Sho.
What kind of fluid goes in a 450 John Deere dozer transmission?
John Deere 450H Dozer hydralic transmission how can drain
How do you replace the drive belt on a John Deere L100 Lawn tractor?
You must back out three bolts which hold plastic cover over left side spindle pulley first. After cover is removed (or at least two rear bolts are removed allowing cover to be pulled up ) work belt onto this pulley and reinstall bolts on cover. Then, you must loosen idler pulley next to pulley you just placed belt on as to thread belt onto idler pulley which has a metal fence mounted on pulley shaft to keep belt on this idler. Belt must then be threaded around on/off pulley and right spindle pulley and drive pulley.
How do you change the belts on a John Deere rx63?
Remove Blade , pull cover off top of transmission remove clip on top of pulley pulley slides up and off shaft remove belt from pulley and guide it thru hole to blade . make sure when installing to put clip on correctly if not pulley can come loose and ruin trans input shaft
Can someone please provide a diagram for replacing drive belt on John Deere 14SM?
Standing behind the mower looking down, the belt comes off the blade, out of the deck, to the left of the first pulley(back of belt is against the pulley), now right between the next pulley and around the pulley on the transmission. You may have to remove, or at least raise the second pulley to get the belt under the guard. Have a good one. Geo
How do you replace the battery on a John Deere 445?
how to replace battery in z425 zero turn john deere mower
How do you I fill my John Deere l120 transmission?
Where is the transmission oil container located?
How do you change a drive-belt on an STX38 John Deere lawnmower?
Changing a JD STX38 transmission drive belt.Today I undertook removing my almost failed transmission drive belt on a John Deere STX38. In order to do so (it had come off both the engine pulley and the transmission pulley but was not broken), I had to unbolt the brake pedal lock pin, and disconnect the front wheel steering bars (cotter pin and washer holding each bar to the front wheel axels). The belt then could be removed as the steering arms pass under the belt when it is in place, and the bars are attached by cotter pin and washer, one set at the wheels, and another set at the steering arms in the middle of the chassis. There is one idler pulley in a v shape and another idler pulley that is flattened between the transmission and the steering arms. The back of the belt pushes against the flattened pulley, and the inside (v side) of the belt passes the v shaped pulley as these 2 pulleys provide belt tension.
