Chevy Malibu

How do you replace the turn signal lever on a 1979 Chevrolet Malibu?

678

Top Answer
User Avatar
Wiki User
2008-08-23 03:55:47
2008-08-23 03:55:47

That would be best if left to a certified technician because of the wiring involved.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

First thing it is a lever. It is underneath the trunk release button.

User Avatar

check cable under seat to see if it is ok! the one going to seat lever. if nessesary replace cable.

User Avatar

Multifunction lever at the left side of steering wheel?

User Avatar

lever pulled out, having trouble getting the lever locked back in place

User Avatar

If your car has a tilt wheel it is operated by a short lever below the turn signal. Pull back on the lever to tilt the wheel.

User Avatar

The turn signal lever is the dimmer switch. You either pull it back or push it in. but also the dimmer switch its self is in the steering column u have to take the steering wheel off to replace

User Avatar

i popped out the trip lever and used a stiff paper clip to get it over the stop pin.

User Avatar

how to replace high/low beam, turn signal lever on 1996 subaru outback wagon

User Avatar

There is no lever; just press the gas tank door and it will release! (-:

User Avatar

dimmer switch is on the turn signal lever, to replace you need to remove steering wheel

User Avatar

Pull the hood release lever that is to the right below the sterring wheel. This will pop your hood a little bit and then on the body of the car, right in the center on the black metal, you will feel a lever, move it towards the direction of the driver. I found this in my owners manual.

User Avatar

It turns out the headlight switch is not a serviceable part on the Subaru Forester. Instead, the entire turn signal lever must be replaced (a $100 part). A brief description of how to replace the turn signal lever follows: First, remove the steering column cover. There are three screws underneath - remove those. Then release the steering column adjustment lever and leave it down. The bottom part of the steering column cover unsnaps from the top part and you should be able to remove it easily. The top part of the steering column cover can just stay there and be moved as necessary to gain access to screws. Next, remove two screws where the turn signal lever assembly attaches to the steering column. Remove the electrical harness and the turn signal lever assembly should just pull straight out. Reverse the process to put in the new turn signal lever assembly.

User Avatar

Lift the hood and look behind the headlight assembly, there you will fine two black colored lever devices. Pull up on the lever devices and the head light assembly will unattach from the vehicle. You are then able to access the sockets and replace your headlamp.

User Avatar

The problem is caused by the headlight switch in the turn signal lever. The headlight switch loosens over time and causes electrical shorts which make the headlight go out when the switch is jiggled. This happens most commonly when indicating in either direction. The fix is to replace the turn signal lever. The lever is approximately $100 and can be easily replaced at home. Unscrew 3 screws on the bottom of the steering wheel column cover. Push the steering wheel height adjustment lever all the way down to remove the cover. The turn signal lever can then be removed by removing the electrical harness and unscrewing the two screws that secure it to the steering column. Reverse the process to put in the new turn signal lever.

User Avatar

A turn signal will be activated once you engage it, to do so is very simple. Usually it is a control built in to a small lever that is on either side of the steering wheel column. To activate all you do is push the lever down to activate the right turn signal and push the lever up to activate the left turn signal. Happy driving

User Avatar

Remove the bolt in the lever perch. For a clutch lever, loosen the cable enough to remove the broken lever and replace the new one. Adjust the clutch cable back and replace the bolt in perch. For the brake (disc brake)) lever, you simply remove the bolt and replace lever, put the bolt back in the perch and you're done. If you have drum brakes, it is the same as the clutch lever routine.

User Avatar

Pull back on the turn signal lever to change from high beams to low beams If the turn signal lever is pushed forward the high beams stay on and if the turn signal lever is pulled back all the way that is the " flash to pass " feature

User Avatar

Turn signal lever assembly can be replaced without removing the steering wheel. See instructions at the attached link question about replacing the headlight switch on a 1999 Subaru Forester.

User Avatar

Grasp lever and pull straight out. it goes back in, by pushing it in.

User Avatar

look on the turn signal lever and it's the turn switch in the middle of the lever.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.