Head Gaskets and Valve Covers
Honda Passport

How do you replace the valve cover gasket on a 1997 Honda Passport?

303132

Top Answer
User Avatar
Wiki User
Answered
2015-02-09 10:36:02
2015-02-09 10:36:02

On a 95 You must remove the upper intake the egr and the coil pack. then the 5mm Allen bolts on the covers them self. there are 10 bolts I think. you should get the valve cover kit with the spark plug seals in it. also get a upper manifold kit. to replace the all the gaskets you need. torque the bolts to spec when you replace them. and don't forget the locktite.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


How much does it cost parts and labor to replace a valve cover gasket on a 1990 Honda Accord 4door.

just remove the 3 bolts on top of the valve cover and lift it out,and theres the gasket.

Dear Honda owner, Valve cover leak? I assume you are refering to an external oil leak from the valve cover, replace the gasket, be sure the new gasket set comes with spark plug seals.

how do you replace the valve cover gasket on a 2002 mitubishi lancer

usually the valve cover gasket and the oil seals on the top of the cover,replace gasket and the also the distributor seal

The valve cover gasket, on a 2004 Jeep liberty, can be found by removing the valve cover. Peel the gasket off of the head and replace with a new gasket.

The valve cover ask it, on a S 40 Volvo, can be replaced by first removing the valve cover. Remove the old gasket and replace with a new gasket.

pcv valve replace every 30000 miles.. bad oil pan gasket, or valve cover gasket

simply remove the valve cover gasket,take the old one off,clean the area well, and replace the gasket,tighten the cover evenly.(if ur gasket is made of corque take care not to break the gasket

how to replace valve cover gasket toyota rav4 2001

how do you change valve cover gasket 2004 hyundai elantra

To replace the valve cover, you will need to break the gasket and the o-rings. The gasket prevents oil from leaking.

To replace the valve cover gaskets on a 2003 Jeep Liberty, the valve cover is removed. The old gasket is then removed from both the valve cover and the manifold (old gasket will come off in pieces on both sides). Then spread the sealant on the manifold, place the new gasket on, then put sealant on top of the gasket and replace the valve cover and bolt down.

I assume you mean the valve cover gasket. You replace it by removing the valve cover and cleaning off the oil gasket and the mounting surface. The install the new gasket and reinstall the valve cover. Tighten it to the specifications the manufacture of your engine recommends.

see this site. www.ehow.com/how_4507846_replace-valve-cover-gasket-toyota.html - 51k -

visit the parts store and look in the chilton manual for your make and model it should have the answers you seek

You have to replace the entire headlight assembly not just the cover.

Replacing a head gasket on a 1.5 liter Honda Civic requires removal of many of the engines components such as the intake manifold, valve cover, and timing belt. After removing the head from the engine it needs to be resurfaced. Replace the old head gasket and machined head onto the block and reinstall all the other components.

take off valve cover throw away old gasket replace old gasket with new put valve cover back on pwn

Pretty easy. Remove the valve cover by loosening the 5 bolts holding it in place. There are a couple of hoses and another screw that will need to be removed as well. If the valve cover has been on the engine for some time, you may need to apply sufficient force in breaking the valve cover/gasket loose from the engine. The gasket lies beneath the valve cover along its edge. The edge is lipped so the new gasket can be placed in this groove. A Honda dealer will typically apply an additional sealer to the new gasket above the semi circular portions at either end of the valve cover, but I don't believe this is required. (Pretty expensive to buy the tube for just one application.) Replace valve cover with new gasket installed. Tighten bolts, replace hoses. Done. ..................................................................................................................................... Not done. Don't forget the O-rings around the spark plug openings in the valve cover. These should come with the new valve cover gasket.

you mean a valve cover gasket i think

Begin by removing the valve cover from your 1995 Dodge. Remove the valve cover gasket and clean the surface. Put the new gasket on and return the valve cover to its original position.

you should only change the gasket if you have to take the valve cover off....... you should only change the gasket if you have to take the valve cover off.......

I have a 2007 ford escape, replaced a valve cover gasket in August 2012, noticed that i have a small oil leak around the gasket.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.