KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: • on the owner's wallet card in the glove compartment • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code To program your own code: 5. Enter factory set code (keypad will illuminate when pressed). 6. Press 1/2 control within five seconds of step 1. 7. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. 8. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. Locks and Security 149 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan featureThe anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts (35 consecutive button presses) at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity. • the remote entry transmitter UNLOCK button is pressed. • the ignition is turned to the ON position. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver's door closed, press the 7/8 control and the 9/0 control at the same time. Locks and Security 150
how do you get the entry codes for expedition eddie bower
Take it to a dealer.
If there is no obvious damage to the wiring, it is probably the electric motor inside the door. This is a very simple fix on the Explorer so I imagine it is also on the Expedition.
if you take off the door panel there will be three studs that connect the mirror to the door
turn your ignition switch off and then on in rapid sucession four times dash lights will blink and code can be reset
Listed on the driver's door post, or somewhere else on the vehicle.
You may have tried this but i have a 2000 expedition and when it sayd door ajar its usually the window part of the hatch that's open....other than that I dunno
The switch can be found under the dash on the passenger side of the vehicle, closest to the door.
Door Code Location... I actually found the door code behind the fuse box area (Driver Side) on my brother's 2000 Ford Expedition EB. There is a big white sticker with 5 numbers starting with number 1####. Hope this helps...
Where is the computer on the expedition located at? (2000 Eddie Bauer) _____________________________________________________________ Door Code Location... I actually found the door code behind the fuse box area (Driver Side) on my brother's 2000 Ford Expedition EB. There is a big white sticker with 5 numbers starting with number 1####. Hope this helps...
There is a reset switch for the electric fuel pump located in the right front passenger footwell , behind ( or by ) the kick panel , just in front of the front door
I have the same question. Only I have a 2004 Explorer Sports Trac XLT.