0
To reset the drive cycle on the OBDII computer of a Honda Element, you can disconnect the negative battery terminal for about 15-30 minutes, then reconnect it. This will clear the stored diagnostic trouble codes and reset the computer. After reconnecting, you should drive the vehicle through a series of conditions to allow the OBDII system to complete its readiness tests. Make sure to follow the specific drive cycle procedure outlined in the vehicle's service manual for best results.
What else can I help you with?
How do you reset the drive cycle on the computer of a Honda element?
You take out the battery and reinsert it.
How do you reset the drive cycle on the obdii computer on a Honda Pilot?
To reset the drive cycle on the OBD-II computer of a Honda Pilot, you typically need to disconnect the vehicle's battery for about 10-15 minutes. This will clear any stored trouble codes and reset the computer. After reconnecting the battery, drive the vehicle under varying conditions (city and highway speeds) to allow the computer to re-learn the engine parameters and complete the readiness monitors. Always refer to the vehicle's service manual for specific procedures related to your model year.
What is the OBDII drive cycle for a Jeep Wrangler?
The average Jeep computer takes about 20-30 minutes of driving to perform all the required tests.
How do you reset the drive cycle on the OBDII computer on a Toyota Highlander?
Disconnect both cables on battery, hold horn down for abouta minute, reconnect battery about 15 minutes later
How do you reset the obdii drive cycle on 2003 Mercedes Benz e500?
How do you reset a e500 mercedes benz drive cycle
How do you reset the drive cycle on the OBDII computer on a Honda civic?
1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. (OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.) 2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. (OBDII checks for ignition misfire, fuel trim and canister purge. ) 3. Hold at a steady state speed of 55 mph for three minutes. (OBDII monitors EGR, air pump, O2 sensors and canister purge. ) 4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. (OBDII checks EGR and purge functions.) 5. Accelerate back to 55 to 60 mph at half throttle. (OBDII checks misfire, fuel trim and purge again.) 6. Hold at a steady speed of 55 to 60 mph for five minutes. (OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.) 7. Decelerate (coast down) to a stop without braking. (OBDII makes a final check of EGR and canister purge.)
How do you reset the OBDII drive cycle for a 2000 Daewoo Leganza?
To reset the OBDII drive cycle for a 2000 Daewoo Leganza, you typically need to disconnect the vehicle’s battery for about 15 minutes. This will clear any stored trouble codes and reset the engine control module. After reconnecting the battery, drive the vehicle under varied conditions—accelerating, decelerating, and idling—to complete the drive cycle and allow the OBDII system to recheck emissions readiness. Always refer to the specific vehicle manual for detailed instructions.
How do you pass vehicle inspection for 97 Honda accord ex V6 motor when test says status not ready?
You need to run the car through it's drive cycle before the computer can perform all of it's emissions tests. Look up the drive cycle specified by Honda, perform the drive cycle, and then it should be all set.
How do you reset the OBDII drive cycle for a 2001 Daewoo Leganza?
To reset the OBDII drive cycle for a 2001 Daewoo Leganza, first ensure that the vehicle's battery is disconnected for about 15 minutes to clear the engine control unit (ECU) memory. After reconnecting the battery, drive the vehicle under normal conditions to complete the necessary drive cycle, which typically includes varied speeds, acceleration, and idling. It's important to follow the specific drive cycle requirements outlined in the vehicle's service manual for accurate results. Finally, use an OBDII scanner to verify that the readiness monitors have reset.
What is the element in the water cycle?
The most important element in the water cycle is water itself. Without it, the water cycle would not exist.
How do you reset the drive cycle on the obdii Honda crv 2002?
To reset the drive cycle on a 2002 Honda CR-V, you typically need to clear the vehicle's diagnostic trouble codes (DTCs) using an OBD-II scanner. After clearing the codes, the drive cycle can be completed by following a specific sequence of driving conditions, which usually includes a mix of idling, acceleration, and steady-speed driving. This allows the onboard systems to recheck and recalibrate various sensors. Make sure to drive the vehicle under varied conditions to ensure all readiness monitors are reset.
Where can you get parts for a CL 77 Honda?
Ohio Cycle and Western Hills Honda
