Not from experience, just a cut and paste from the freel2.com web site:-
1. Insert key in ignition.
2. Press AND HOLD the trip reset button.
3. While still pressing the trip reset button, turn on the ignition. DO NOT START THE ENGINE. Just turn the ignition on.
4. Keep pressed the trip reset button until word "Service" will flash on the instrument cluster. (about 5 seconds).
5. After a while (no more than 5 seconds) the word "Service" will remain on.
6. Release the reset button.
7. Now, by pressing the reset button, the words DIST, DATE and END are cycled on display.
8. If you want to reset the service distance, cycle until DIST is shown. If you want to reset the time-to-service, cycle until DATE is shown.
9. When the desired item is selected, press and KEEP pressed the reset button until the word RESET is shown.
Do this for both items or only for the one you desire. (I've did it only for time)
10. When you've done, cycle until END appears and then press and HOLD reset button until the display will now show the current (and newly reset) distance and time until next inspection.
11. Turn off the ignition.
12. All done!
A combination of pulling and pushing the 2 speedo buttons at the same time. This should reset the service light.
Service indicator reset switch ignition to position 2 press brake & accelerator pedals together for 15 seconds service indicator will flash when reset release pedals turn ignition off hope this was useful Mike 2
any shop or dealer should be able to reset it, they have to plug into your car just under and to the left of your steering wheel, using a handheld to pull and clear any codes. hope this helps. or try this : 1. Turn Ignition key to position1 2. Press and hold reset button for the trip meter 3.Switch ignition ON 4. Keep Depressed for 10 secs. Service indicator will flash. Release reset button within 5 secs. There will be an audible signal when reset completes & service indicator goes out. * if reset button is not released within 5 secs , the service interval indicator will not be reset but will stop flashing. Good Luck!
Key in position 2, scroll to service due screen then hold down reset button on the cluster for a few seconds, then it will ask if you wish to reset button. Push button on the cluster again to reset. MAKE SURE DOOR IS SHUT
To reset the service indicator on 1998 Mercedes Benz C200 . Turn the ignition key to position 2 and press the 0 on the left of the cluster twice. Then turn the key to position 0 Then press and hold the 0 button on the left of the cluster whilst turning the key to position 2. Continue holding the 0 button until you hear a signal or beep. Release the 0 button after you hear the beep. Service indicator will then reset.
Hold in the wrench button on instrument cluster, and at the same time turn your key forward (without starting). While still holding the "wrench" button in, press the "0,0" button and hold until the "SERVICE!" notification clears (about 2-3 seconds). "Service!" Indicator Reset Procedure/Service Indicator Reset Complete!
Turn Key to position 1, hold in trip odometer reset while turning key to position 2. Hold down until service reminder starts flashing, then release odometer reset.
Most likely the same as the 2000 E430 which is as follows: turn key to position 1 press up or down arrow til service indicator appears press and hold (R) button for approx 2 seconds display will show "do you want to reset service interval?" press (R) button again to reset Hope that works for you.
On the dashboard browse through the menu until you see the "You have exceeded the service by ... days" then click and hold the reset button for about 2 seconds (its the thingy that you rotate on the side of the dashboard) It will ask you to confirm, click on it again.
Resetting the Service reminder indicator (SRI), model years -2001 The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The lamp remains lit for 120 seconds when the ignition is switched on. Note! If the lamp flashes, it may be because one of the service parameters has not been programmed. Proceed as follows to reset the service reminder indicator (SRI): -Ignition position I -Press and hold in the reset button for the trip odometer -Ignition position II -The service reminder indicator (SRI) starts flashing when the reset button for the trip odometer has been pressed for 10 seconds -Release the reset button for the trip odometer within 5 seconds. The instrument gives an audible signal when resetting has succeeded. Note! If the trip meter reset button is not released within 5 seconds the indicator is not reset. However the indicator will stop flashing. Resetting the service reminder indicator (SRI), model years 2002- The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120 s each time the ignition is switched on. Proceed as follows to reset the service reminder indicator (SRI): -Ignition position I -Press and hold in the reset button for the trip odometer -Ignition position II. Note! Turn the key to position II within 2 seconds. -Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released. -Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded -If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds. Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.
My 2005 Chevy 4wd, ext. cab,shrt bed, has push buttons to go from(from top to bottom) Auto 4wheel drive, to 2 High , then to N(neutral), and then to 4 high, then to 4 low. At approx. 50,000 mi. the service indicator light came on and indicated "Service 4wd." I re-set the indicator, and forgot about it. Now, at 63,000 mi. it's telling me to service the 4wd, only this time the reset works until I turn the ignition off. when I restart, the service light comes on. However, the indicator lights that show which gear the transfer case is in, does not light up, and there is no automatic shifting of the transfer case. Is there a simple solution to this problem? Recommendations...Please! popo63
key in position 2, scroll to service due A or B then hold down reset button on the cluster for a few seconds, then it will promt you to push button and hold again. It should reset now and tell you will you next change is due. Make sure you door is shut.