0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why is the gas not going in the prime bulb of a Craftsman 25cc Gasoline Weedwacker?
If the bulb is cracked or the line going to it is it will not work, also make sure the hose going to it is submerged in the fuel. another possibility is that the vent hose is plugged and the tank has too much vacuum pressure to allow the fuel to be sucked up.
What size line does craftsman 17 25cc weed wacker take?
1/8" feed line 3/16" return line.
What is fuel line diagram for Craftsman Weedwacker 32 cc?
Diagram showing where the lines from the fuel tank go at the carburetor and the primmer bulb.
What is the oil to gas ratio for a craftsman 17 25cc weedwacker?
If it was made in the last five years or so, it should be 50 to 1. The above answer is incorrect for my Weedwacker. Craftsman Weedwacker 17"/25cc Gas Line Trimmer 2003 US EPA PH2 Family: 3PWES.0254TZ Disp: 25cc : EM Serial: [redacted] Model: 358.795543 Emission: durability period 50 hours Customer questions: 1-800-235-5878 IMPORTANT! Mix CRAFTSMAN 40:1 2-cycle engine oil with unleaded gasoline. Read oil container or operator's manual for proper mixing instructions. Other oils may cause engine damage. 1. Place stop switch in "ON" position. 2. Set unit on flat surface. 3. Slowly press the primer bulb 6 times. 4. Move choke lever to "FULL CHOKE" position. 5. Squeeze throttle trigger fully and hold [thru step 6] and pull starter handle sharply until engine attempts to run. NO MORE THAN 6 PULLS. 6. Move choke lever to "HALF CHOKE" position and pull starter handle until engine runs. 7. Allow engine to run for 10 seconds, then move choke lever to the "OFF CHOKE" position. TO STOP ENGINE MOVE STOP SWITCH TO "OFF" POSITION. The above three paragraphs are verbatim from three stickers on my Weedwacker. The stickers have no copyright on them. The simple answer to your question is, "40:1 2-cycle engine oil with unleaded gasoline." rcpao 2008-06-29 22:03
How do you untangle the line on a kid's Zebco fishing pole?
Theres a reason they sell spare spools of line. Its easier to cut away the rats nest and pull out more line or respool the reel with new line that trying to fight that dilemma. The quality of line used on those combos isn't the greatest to begin with. Trilene 6 or 8 pound test is more than enough for that type rod and fishing conditions.
How do you attach fuel line on Craftsman Weedwacker model 358.797150?
drain the fuel, remove the fuel filter from inside the tank, remove the old fuel line from the filter, remove the old fuel line from the carb, pull old fuel line out, install new fuel line through the tank, reconnect fuel filter to new fuel line, place filter and slack line into tank, connect new fuel line to carb, refill tank, check for leaks.
If you have a Craftsman 32cc Weedwacker and the fuel line from the tank element to the carb has fallen apart and the element filter is lose in the fuel tank - How do you go about fixing this?
Dump all of the fuel out of the tank. Then take a pair of long needle nose pliers and grab the end f the fuel line. Inspect it for swelling or complete disentegration. The ethanol added to gas that is now mandatory in many states is very tough on fuel line. You may have to replace the fuel line and put a new fuel filter on while you're at it. Patience is a virtue.
What is the oil to gas ratio on craftsman 32cc weedwacker?
40:1 is the correct mixture for the fuel and 2 cycle oil. 3 oz. of 2 cycle oil per gallon of gas. I have Craftsman Line Trimmer 358.795190 (Model #). It has the quick release shaft for other attachments. Hopefully this will help you.
How do you hook up gas lines for craftsman weedwacker model no 316 798221?
The process will vary between models. The lines should be fit into the tank tightly, with no gaskets. There may be an internal filter in the tank, it plugs on the end of the suction line. The other ends of the lines slide tightly onto the carburetor fittings.
How did Henry Ford system increase efficiency in his auto plants?
Ford's innovation of the assembly line allowed for building automobiles in a fast and efficient manner. Instead of having individual craftsmen basically build each automobile. The assembly line put workers to add parts as the vehicle moved down the line. Each stop on the line allowed workers to add and adjust parts. This allowed for faster production time, and Ford also paid his workers well compared to other industrialists.
Manual for Craftsman 31679116?
Go to Sears.com, then at the top of the page, click on Parts Direct. A box will appear where you can enter the Model #. On the page that comes up, click "View Manual". A .pdf file will open which you can save to your computer.
What were Gilts in Medieval Times?
If you mean "guilds," they were associations of craftsmen and tradesmen according to their line of work: guilds of candlemakers (chandlers), textile workers, stonemasons, silversmiths, carpenters, etc. The guilds protected and passed down the secrets of their crafts and also gave their members certain privileges. No - It is definitely Gilts - They were associated with the Catholic Church in medieval times Grateful for any help
