0
How do you set default root in a router by using dynamic routing?
Wiki User
∙ 11y ago
If the network uses the RIP protocol, router A will determine that all paths have equal cost.
If the network uses the RIP protocol, router A will update only the A-C-E path in its routing table.
If the network uses the EIGRP routing protocol, router A will determine that path A-D-E has the lowest cost.
If both RIP and EIGRP protocols are configured on router A, the router will use the route information that is learned by the RIP routing protocol.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
When should you use a default route?
When you have routing enabled then you need default route (also calleddefault network or Gateway of Last Resort). You do not need default routeif you don't use routing. For example if you just have one router in your network there is no need for default route. When you have more than one router in a network you need default route.Note: If you connect to WAN (Internet) you need default route. The default route allows connection with Internet. If you are not using WAN and have one router than there is not need for default route but in these days everyone connects to the Internet so most likely your router has default route. When using router to connect to the Internet using DHCP this happens automatically so there will no need to configure default route manually. If you need to manually set default route then use the commands IP default-network or IP route 0.0.0.0 0.0.0.0 .More info can be found at Cisco's site - see the related link below.
Differentiate between static and dynamic routing algorithms?
* Manually set up a route in a dormant manner. * Stable. * Has no impact made by traffic and transmission failures. * Creates no traffic derived from routing protocols. = dynamic routing: = * Automatically sets up a route. * Can respond to the changes of the network. * Can automatically select the optimized route. * Can automatically select the backup route.
What are the default settings for a Linksys modem router?
The default username and password for a Linksys modem router should be "admin" and "admin", the same thing for both. You can reset your router by using the reset button the back of it.
What is routing in networks?
This is when network routes are manually entered into a router's configuration, as opposed to using a routing protocol to automatically determine routes.
A router has learned two equal cost paths to a remote network via the eigrp and rip protocol are using their default configurationswhich path to the remote network will be install the routing table?
the path learned via EIGRP
What is static routing in networking?
This is when network routes are manually entered into a router's configuration, as opposed to using a routing protocol to automatically determine routes.
What information is required by a router to successfully route packets?
To route a packet, usually an IP packet, a router compares the destination address to its (the router's) routing table. The router can get entries (rows) in its routing table in three different ways: (1) directly connected networks; (2) static routes (the route was configured manually by an administrator); (3) dynamic routes (the router learned available routes from a neighboring router, using a routing protocol such as RIP or OSPF).
What are the three valid VLAN routing methods?
Router-on-a-stickRouter-on-a-stick using trunksLayer 3 switching
My DS says the Sky Router WEP key is wrong?
Are you sure the Sky Router is using WEP? The default is WPA, which a regular DS cannot decrypt.
What forwards packets to networks by using a decision-making process on routing table data and discouvery of routes?
That should be a router.
What is RIP Listener in Windows 7 features?
If your router or routers are using Routing Information Protocol version 1 (RIPv1), the RIP Listener service can be turned on to listen for updates sent by the router(s). It will add the new routes to the routing table on the local machine.
How do you connect the wireless router to a dsl modem?
The question would be easier to answer if you included the specific model # of the Netgear router you are trying to configure. You can not connect a netgear router or any other router directly to a DSL line unless it also functions as a DSL modem. You can connect a router to a DSL modem which connects to a DSL line.
