0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you set the timing belt on a 1996 Plymouth Breeze 2.0L?
Get a manual on your car.
Where do you set crank and cam shaft marks to set timing on a 1996 Nissan Pathfinder?
Where do you set crank and cam shaft marks to set timing on a 1996 Nissan Pathfinder?" Did the timing belt snap ? if so the engine will have bent valves and require more work than just the belt. This is timing belt job is not one for the inexperienced diy mechanic. Not trying to be a wise guy, but get the manual, the timing mark set up isn't a simple explanation .
What is the timing set on for 1999 Kia Sportage 4 wheel drive?
needing to know how to do the time belt for a two wheel drive kia sportage.
What is the pattern for the deck belt on a John Deere 318 lawn tractor?
John Deere 318 Onanhorizontal-shaft engine has a front-mounted PTO electric clutch that drives a pulley. A tension-adjusting spring-loaded double-pulley set is frame-mounted below the electric-clutch. This drive set has two pulleys attached parallel to each other but on opposite sides. Their axis is 90 degrees rotated compared to the PTO pulley. That drive set is attached to the frame by pins which fit into frame slots. Belt tension holds it in place. Insert your belt loop up through the drive set, wrapping it onto both drive pulleys. If you wish, you may remove the drive set from the frame to start the belt fitting, but that's not necessary. Rotate the front drive set's spring-tension-adjusting knob until its indicator points to the position marked as "Install." Wrap the belt around the PTO clutch sheave which twists the belt a quarter turn between the PTO pulley and the two drive set pulleys. The belt runs down from the PTO clutch pulley, twisting 90 degrees onto the two drive set pulleys, then horizontally back, twisting in the opposite direction another 90 degrees then wraps around mower deck's drive pulley. To provide some slack during fitting, push the spring-loaded right-side drive set pulley "up" into the spring tension. After fitting the belt with V-side seated into each pulley wrap, rotate the mule drive's spring-tension adjusting knob until its tension-indicator points toward the drive set top. That applies the factory-suggested belt tension preload. If you encounter belt slippage during wet conditions as may occur when cutting juicy weeds which reduces belt-to-pulley friction, consider increasing belt pre-load tension as a compensation strategy. The factory spring-pre-load tension balances slippage against belt service life for the most commonly encountered conditions. When conditions are dryer again, reduce belt tension back to factory suggested value.
How do you change a drive belt on a ford new holland LS55 lawn tractor?
Not an easy task. Never had to remove steering rods and break shaft set up to install a drive belt on a mower before.
How do you replace the drive and variable speed belts on MTD 14AZ808K131?
Set the parking brake and disconnect the spark plug wire. Remove the cutting deck and the battery. Loosen the pulley and remove the upper belt. Remove the belt guide and the belt keeper. Loosen the bolt on the crankshaft pulley. Remove the lower drive belt.
Where is the adjuster bolt to release fan belt tension on a 1995 Achieva Oldsmobile?
You have no "adjuster bolt". You have a serpentine drive belt and it's tension is maintained by an automatic belt tensioner. It is a pulley mounted on a housing containing a "clock spring" that keeps the belt under a pre-set tension and compensates for belt-wear. It is released by a special belt tool or a flex-drive handle. Mark---Raleigh, NC
How do you replace the drive belt on a 1991 Mitsubishi mighty max truck?
Need a diagram to set the timing Mitsubishi 1991 pu
Where do you set the timing marks for a 1996 Mercury Villager?
belt it self has timing dots on it, line it up with cam dots and crank dot.
Is it against the law to drive without a seat belt?
Seat belts are legally required in most jurisdictions. Wear your seat belt.
If you remove the supercharger belt on a 3.8l GTP are you going to have poorer gas mileage I know you will lose power?
do not remove your supercharger belt, the engine is set up to work with supercharger. my belt broke on mine and i was told to replace it before i drive it to much
How do set set timing on a Toyota solara 2.4 after the belt is replaced?
If you're referring to cam timing you don't. That's set when the belt is installed by matching up timing marks on the cam drive wheels and the crankshaft. If any of those marks is off even by a single notch in the belt the engine won't run correctly. If you're referring to ignition timing, you still don't. That shouldn't have changed at all during a belt replacement.
