0
How do you stop hackers from getting into your network from DSL cable side?
Wiki User
∙ 15y ago
It dependens on what kind of a router you have. But the basic technique is to turn the firewall in your router, and change the administrator password. If it didn't help to turn on ip-filtering it will help immedeately but requires time if you have many computers connected to your router which you don't want to block. You have to block Ips of hackers and make a blocking rule or add all your friends Ips and make a rule allowing only described Ips.
Wiki User
∙ 16y ago
Wiki User
∙ 15y agoA good firewall, and anti virus. You might want to look for some guilds to make your network save, it will help a lot.
Add your answer:
Earn +20 pts
How do you punch Network cable in patch panel and color code both side?
This depends on the cable or direct satellite company you are using to access cable on your television. In most cases, you can hold both the side and the front. From there, hold the remote.
Your laptop shows a network cable is unplugged when trying to connect internet?
Check to see if the network cable is unplugged. Push it in to make sure it isn't loose. If you're using wireless, you can ignore the message. It's just telling you that you are not connected to a LAN network, which requires a network cable. If you are not using wireless, and the network cable is plugged in securely, then use the Network Troubleshooter to troubleshoot it. Go to Start, Control Panel, Network and Internet Connections and you'll see the icon for the troubleshooter on the left side of the screen.
How do i wire a laptop through a router to the internet?
first, make sure the router is wired to your dsl/cable modem (network cable is pluged on your router's internet port & the another of that goes to the port of your modem). Get another network cable, plug it to your laptop (there's one or two socket that fits that network cable on any side of your laptop), then plug the other end of the network cable to any port numbers of the rtr.....hope that'll help! ;)
How do you identify the presence of a network ready printer?
Just check behind or on the right side of the printer where there will be a square hole. If your network cable fits in it, a GRAND SUCESS!
Why are hackers and malicious code writers winning the battle over internet security?
Because everyone wants to be on the side of hackers not the feds and the hackers are almost always smarter and are more devious.
If a house is already wired for cable but not connected to the cable coming into the house can you make those connections yourself?
Many home now are being wire in what is called structural wiring where as all cable/network/phone cables are pulled to a central location inside the home. As long as the entrance cable from the outside is connected to the customer side of the Network interface unit there should not be a problem. No. If you are paying for cable the cable company is responsible for hooking it up for you. If you are not paying hooking it up yourself is theft.
What color or stripe down one side of a cable marks this side of the cable as 1 pin?
red
Can you lay a network cable next to a power cable?
If the network cable is a standard copper cat5/6 cable I would recommend keeping them at least six to twelve inches apart IF they are running side by side along a path. If they just cross at one point it's not likely to cause an issue for you. However if you're using STP (Shielded twisted pair) or fiber optics, lay them as close as you like and you'll be fine since crosstalk is not a serious concern with shielded cable or even possible at all with fiber optics. Regardless, you're not LIKELY to have any issues, but playing it say I'd say six inches at least. Hope this helps!
What is the tap off in cable network?
Tap off in cable networks is a point in the network where a branch cable is connected in order to connect a customer or a subscriber. It is usually done by a splitter or a coupler. Tap off points are also used to measure the signal strength or to monitor the quality of the transmission. The tap off point is usually connected from the main trunk cable to the side branch cable. Tap off points are also used to connect amplifiers and other devices in the network. Tap off points are used to connect branch cables to the main trunk cable. Tap off points can be used to measure signal strength or monitor transmission quality. Amplifiers and other devices can be connected to tap off points.
What are rail network going to do with the cafe near the viaduct on the sea side in Dawlish Devon?
Can I advise either closing it or getting someone with manners to run it.....
how do I get my password from Wifi?
Obviously, passwords can always be changed and the place to get it will change all the time. For home wifi from a cable/network company, however, the password can almost always be found on the side of a provider router.
1990 Corvette driver side release on hood doesnt work?
That's common; you need to put a "splitshot" between the cable and the small bolt on the right side cable so it "shortens" the cable about 1/8 inch.....The cable gets a "little" slack and it alway sefects the right side...
