0
The entire taillight comes off as an assembly, and is not designed to be taken apart.
To change a light bulb:
1. Inside the trunk look on the back side of the taillight near the quarter panel. There will be 3 nuts, the center nut holds the taillight assembly in place, remove that nut.
2. Pull the assembly rearward enough to bring the stud out from the header panel, then pull the tab out of the license plate light assembly.
3. Remove the socket that needs a new bulb and replace the bulb, then slide the taillight assembly back in place and put the nut back on.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you change the front right turn signal on a 1989 Chevy Celebrity?
To change the front blinker bulb on your 1989 Chevy Celebrity simply reach up behind the bumper and unplug the socket from the fixture. Replace the bulb in the socket and plug the socket back into the fixture.
How do you change a taillight on a 1997 ford explorer?
Open the liftgate Remove the 2 screws at the top of the taillight assembly Carefully " work " the taillight straight back towards you . There are plastic pins shaped >>>>>>>>>>>> that hold the taillight assembly in place The bulb sockets are a simple turn to remove / install
How do you put a 89 Chevy Celebrity back in time when it jumps time?
The 1989 Chevrolet Celebrity uses distributorless ignition. The spark is controled by the ECM, engine control module, and cannot be re set, or go out of time.
How do remove taillight cover on a 01 Monte Carlo?
it has wing nuts on it to hold it in place, it comes off by opening the trunk and the wing nuts are in back of the taillight inside the trunk.
How does water pump pulley come off a 89 celeberty 2.5?
A special puller is required to remove the water pump pulley from a 1989 Celebrity. The tool can be "borrowed" from Autozone on their "loner tool program". The same tool kit contains another tool to press the pulley back on. I did the job on my 1989 Celebrity with 2.5L, it was not difficult with the tool.
How do I open to check the bulbs 1992 Chevy Silverado back running lights do not work backup turn signals brake lights all work just no back running lights?
Open tailgate. Remove 2 torx screws in side of taillight. wiggle taillight out, Remove hex screws that hold bulb assembly in taillight. change bulb, Reassemble
How do you change a 1994 doge intrepid brake light?
You just have to pull back the trim in the trunk to access the fasteners for the taillight assembly. Once you remove the taillight assembly just replace the bulb.
Where is the battery on a 2009 BMW 528i?
in the back trunk, usually on the right side near the taillight~
How do you remove the taillight housing on a 2007 Dodge Magnum?
Pop the cover off the inside of the pockets in the rear hatch. Remove the wing nut (don't drop it) .On the outside pull the taillight straight back.
How do you remove the rear taillight on a 1988 Chevrolet celebrity?
To remove the tail light assembly on a 1987 to 1989 Chevy Celebrity: On the inside of the trunk next to the quarter panel look for the nuts that hold the rear header to the body. Remove the middle nut, which will be in the center of the tail light assembly. the assembly will then pull outward. When the stud clears then pull to the outside of the car to release the tab from the back up light assembly. If you remove a nut but the tail light assembly did not budge then you probably removed the wrong nut. I like to replace the original nut with a wing nut. That makes future removal easier.
How do you remove the taillight of a 1998 Ford Explorer to replace bulbs?
Open the lift gate , remove the ( 2 ) screws at the top of the taillight , carefully work the taillight straight back towards you ( it has plastic pins >>>>>>>> that hold it in place and you don't want to break any of those ) The bulb sockets are a simple turn to release
Why did 'Miley and Nick' break up?
Because they were fighting and It just wasn't fun. But they are back tofether.because they both have a hectic scedhule
