0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you thread a ford 532 wire hay baler?
Run the twine out of the twine box and through the guide next to the needle. Then run the twine through the needles and tie it off somewhere. When the knotter trips, it will inject the twine into the knotters and it will be threaded. If your baler has been sitting for awhile, it might take a few cycles for it to start knotting properly due to rust. for starters if it's a wire baler it doesn't have twine or knotters; it has wire and twisters. but it's true you thread it through the guide holes in balewire box, down through the sheaves, up over sheaves just before the needles and across the top of the needles then tie it off to the brace just like a twine baler. be careful, make sure it's centered over the top of the needles. after it makes a cycle you should be able to see if it picked up the wire and has held it in twisting grippers. it is held in these until the wire goes around the bale, then it should twisted and cut. make sure sheaves that wire goes through are lubricated with wd40 or something similar. i bought my 532 about five years ago and it does a good job. i think you can still get a manual for this baler from your ford ag dealer.
How do you thread a john deere 336 wire baler?
Threading the WirePlace a box of twine or wire in each of the two holding brackets at the rear of the baler. Remove the cardboard discs in the center of each box and locate the end of the twine or wire on the inside of the coil.2Pass the end of the twine or wire from the right-hand box through the ceramic spool on the right-hand side of the ejection chute.3Pass the end of the twine or wire into the bottom opening of the right-hand threading needle. Pull the twine or wire out through the top of the needle.4Pull the twine or wire taut and tie it securely to the eyebolt, just ahead of the right-hand threading needle.5Repeat the procedure for the left-hand threading needle.If the twine or wire snaps when you engage the baler, you may have gotten the loose end from the outside of the coil instead of the inside. Check to ensure that the end of the twine or wire does not pass under or into the coil inside the box.- If the wire snaps, you started the wrong end from the box of wire. Pay attention to the "Start this end" tag.
What are the components of baler?
An input area, a compression chamber, hydraulic arms or rams, wheels, hydraulic cylinders, and tying mechanisms are all common industrial baler components (twine, rope, netting, wire, strapping, etc.).
Another name for a thread guide is?
Yarn guide / Wire guide
Another name of single strand wire?
Another name that can be used for a single-strand wire is thread or strand.
How do you wire a bicycle dynamo?
EASILY. jUST THREAD THE WIRE THROUGH THE HOLES AS SHOWN IN THE INSTRUCTIONS THAT YOU CAN GET POSTED TO YOUR POSTAL ADRESS.
In surgery the seams formed by joining two bodily surfaces with thread or wire?
sutures
What is the meaning of wire?
A thread or slender rod of metal; a metallic substance formed to an even thread by being passed between grooved rollers, or drawn through holes in a plate of steel., A telegraph wire or cable; hence, an electric telegraph; as, to send a message by wire., To bind with wire; to attach with wires; to apply wire to; as, to wire corks in bottling liquors., To put upon a wire; as, to wire beads., To snare by means of a wire or wires., To send (a message) by telegraph., To pass like a wire; to flow in a wirelike form, or in a tenuous stream., To send a telegraphic message.
How do you Use filament in a sentence?
(Filament is a thread or thin wire.)Is the lamp unplugged or is the filament broken in the bulb?A silkworm's cocoon is made from a thin filament which can be twisted into thread.
How do you make a Wire's Jacket?
A: When a wire is drawn some means of depositing plastic covering to the wire is required so for adhering a very small thread is placed along the wire so the plastic can have some means of adhesion to the plastic
What is spools?
I found this answer in a dictionary:# ## A cylinder of wood, plastic, cardboard, or other material on which wire, thread, or string is wound. ## The amount of wire, thread, or string wound on such a cylinder. ## Something similar to such a cylinder in shape or function. # A reel for magnetic tape.I hope this helps answer the question.
How do you clean rusted thread on galvanized pipe?
I find a wire brush is usually enough to clean threads.
