0
To tighten the chain on a 1987 Honda FourTrax, first, place the ATV on a level surface and elevate the rear with a stand. Loosen the axle nut and the two lock nuts on the chain adjuster bolts. Turn the adjuster bolts evenly on both sides to achieve the desired chain tension, ensuring the chain has approximately 1 to 1.5 inches of slack. Once adjusted, re-tighten the lock nuts and axle nut securely.
What else can I help you with?
What size is the stock carburetor on a 1987 Honda trx 250 fourtrax?
A carburetor for the 1987 Honda TRX250 Fourtrax isÊsized to be directly plugged into the motorcycle. Replacements are made for restoration toÊfactory specifications.Ê
How much oil will a 1987 Honda 350 fourtrax take?
2.7 quarts
Where is the battery located on a 1987 Honda fourtrax 125?
it is located between the rear fenders
Where can I get a wiring diagram for a 1987 Honda fourtrax 350?
Simple answer is to buy a workshop repair manual
How much is a 1987 Honda 350 ATV worth?
If your Honda fourtrax is in "Excellent shape" it is still worth $900 listed in MudTerrain Motorsports.
How do you set timing on a 1987 350 Honda fourtrax ATV?
To set the timing on a 1987 Honda FourTrax 350 ATV, first ensure the engine is off and cool. Remove the timing inspection cover and locate the timing mark on the flywheel, then align it with the mark on the engine case while rotating the crankshaft. Adjust the timing by loosening the stator bolts and rotating the stator until the timing marks align, then tighten the bolts securely. Finally, replace the inspection cover and start the engine to check for proper timing.
What type of oil is needed for 1987 Honda TRX350 fourtrax 4x4?
10w40 made for wet-clutch engines will work just fine
How do you tighten the chain on a 1987 Honda trx 250x quad?
on the rear axle housing, sprocket side, there should be a large spanner nut. Loosen the two bolts that tighten the rear axle in the housing and turn that spanner nut. Not sure which direction, you should be able to figure that out.
What is the fuel oil mix ratio for a 1987 Honda fourtrax trx200sx?
isn't this four wheeler a four stroke , if it has valves its a four stroke and does not require a premix
What is the Valve clearance 1987 Honda Fourtrax 4x4?
The valve clearance for a 1987 Honda Fourtrax 4x4 (TRX350) is typically set at 0.004 inches (0.1 mm) for both intake and exhaust valves when the engine is cold. It's important to adjust the valve clearance periodically to ensure optimal engine performance and prevent potential damage. Always consult the owner's manual or a service manual for specific guidelines and procedures.
Is a 1985 Honda fourtrax 250 starter reduction gears compatible with an 86 or 87 Honda fourtrax 250 starter reduction gears?
The starter reduction gears from a 1985 Honda FourTrax 250 are generally not compatible with the 1986 or 1987 models due to differences in design and specifications. While the overall engine and transmission may appear similar, manufacturers often make subtle revisions that can affect part compatibility. It's best to consult a parts manual or a dealership to confirm compatibility before making any replacements.
What are the valve lash specs for a 1987 Honda foreman fourtrax 350?
The valve lash specifications for a 1987 Honda Foreman FourTrax 350 are typically set at 0.002 inches (0.05 mm) for both the intake and exhaust valves when the engine is cold. It's important to adjust these clearances to ensure proper engine performance and prevent potential damage. Always refer to the service manual for any specific adjustments or procedures related to your model.
