Best Answer

A loose armrest in a 1992 Ford Ranger on the driver's door can be tightened by removing it and using a larger screw to put it back in. An armrest attached to the driver's seat could be tightened by inserting a larger bolt after the old bolt is cut out. To take the bolt out without cutting it will require cutting into the upholstery.

2014-09-18 00:21:59
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: How do you tighten a loose arm rest on a 1992 Ford Ranger drivers seat?
Write your answer...

Related Questions

Where is the icm on a 1992 ford ranger located?

The 1992 Ford Ranger ICM is located on the firewall in the engine compartment. The ICM will be on the drivers side of the firewall.

Should the drivers seat on a 1991 YJ be loose?

I have a 1992 YJ, and the seat is not loose. I don't think it would be safe to have a loose seat.

Where is starter on 1992 ranger 4.0 liter?

On your 1992 Ford Ranger , 4.0 liter : The starter should be on the drivers side of the engine , low down , where the transmission bolts to the rear of the engine

Why did my serpentine belt slip off can you tighten it its loose now and wont recharge battery?

1992 4.3l engine

Where is the pcv on a 1992 Ford Ranger efi?

The PCV valve on a 1992 Ranger 3.0 V6 is on the drivers side and fits into the manifold cover near the firewall. There are 2 hoses which conect to the top of the PCV Valve.

How do you replace the fuel filter on a 1992 Ford Ranger?

where is fuel filter located on a 1992 ford ranger

Where is the kickpanel located on a 1992 Ford Ranger?

The kick panels are the interior trim panels , just in front of the front doors , by the front passengers and drivers feet

Where oil sending unit on 1992 Ford Ranger?

Where is the oil pressure sending unit on 1992 ford ranger

Owners manual for a 1992 Ford Ranger XLT?

What is a a/cl dv on a 1992 ford ranger xlt vacuum line

Change a tie rod on a 1992 Ford Ranger xlt?

how to change a tie rod on a 1992 ford ranger xlt

1992 Toyota Celica wont start just clicks why?

Clicking can mean a loose connection between battery and starter. Follow wire to starter and clean/tighten connector at starter.

Where is the daytime running lights module location on a 1992 ranger?

The 1992 Ford Ranger did not come equipped with daytime running lights.

1992 ford ranger pulling to left?

check tire pressures. if ok rotate tires left to right front only if it pulls right its in the tires. dont forget to tighten the wheel nuts

Will a 1990 ranger door fit a 1988 ranger?

doors from 1986 to 1992 are the same for ranger bronco. yes will fit

What degree thermostat goes in a 1992 4.0 Ford Ranger STX?

The 1992 Ford Ranger 4.0 liter had a 197 * Fahrenheit thermostat from the factory

Is the fuel pump for a 1992 Ford Ranger electric or mechanical?

A 1992 Ford Ranger is fuel injected so it would have an ELECTRIC fuel pump

How do you change upper and lower ball joints on a 1992 ford ranger super cab 2wd?

how do i change a lower ball joint on a 1992 ranger 2wd

How do you stop a belt from squealing on a 1992 Geo Prizm?

It is squealing because it is loose or worn out. Tighten it and if that does not help, replace it. If it is a serpentine belt, just replace it and check to make sure the idler tensioner is working properly.

How do you tighten the side mirror in a 1992 Lexus SC400?

You have to remove the plastic piece in the inside of the car which will expose the bolts to tighten the mirror

How do you remove a governor in a 1992 ranger?

Cant Its the computer

How do you adjust the parking brake on a 1992 Nissan sentra?

Tighten it up!!

Where is the carburetor on a 1992 Ford Ranger 3.0L V6 ...or would it be fuel-injected?

I own a 1992 ford ranger, 300c.i. v-6 and it is fuel injected.

What is the oil capacity on a 1992 ford ranger?

5 Liters

Change oil pan 1992 Ford Ranger?


Do you have a diagram for a 1992 Ford Ranger 3.0 engine?

You can get a diagram for a 1992 Ford Ranger 3.0 engine from your local auto parts store. Repair books, such as Haynes, offer diagrams.