0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you turn off the seatbelt alarm on a 2000 Toyota Tundra?
Well you should always wear a seatbelt but you can turn off the chime by simply grounding the wire lead at the seatbelt causing the electricity to flow through and the chime to turn off
How do you turn off the seatbelt chime on a 2006 Acura RSX using the dash computer interface?
buckle your seatbelt
How do you turn off the seat belt warning chime on a 2007 odyssey?
Put on your seatbelt!
How do you turn Nissan seatbelt warning chime off when it goes off with no one siting on seat?
how about just fastening the seatbelt when no one is using it.......
How do you turn off the seatbelt chime on a ford ranger 2003?
If you connect you seatbelt for about a minute or two, then take it off, it should shut off.
How do you turn off a seat belt chime on a 2017 Dodge Charger?
You follow the law and wear the seatbelt.
How do you turn on interior light in jeep wrangler?
this is nice
Where is the fuse for the seatbelt chime on a 2008 dodge caliber?
There is not an individual fuse for the seat belt chime. Check your owners manual for the "enhanced saftey system" for a method to turn it off.
How do you turn off the seat belt chime in a 2005 Chevy pickup?
the seatbelt chime and door chime is hooked up to the stock radio in all gm vehicles just find somebody that knows car steros
Where is the turn signal flasher for 2001 jeep wrangler?
The 2001 Jeep Wrangler turn signal flasher relay switch can be located beneath the dashboard. The switch will be on the drivers side of the engine compartment.
How do you make your seat belt chime stop on your 2008 dodge ram?
To turn off the seatbelt chime in 2006-2008 Dodge Rams and some other newer Dodge vehicles, follow this procedure: Get in the vehicle, close the door, put on your seatbelt. Start the engine, wait for the seatbelt light to turn off. Within 30 seconds of the light turning off, unbuckle and re-buckle the seatbelt 4 times, making sure the seatbelt light responds (turns on and off) each time you unbuckle and re-buckle the belt. Ending with the seatbelt BUCKLED, turn off your engine. If done correctly, you will immediately hear one chime to verify the programming. To re-enable the chime, simply repeat this procedure. NOTE: Although the seatbelt chime will not chime constantly if your belt is not buckled while driving, it WILL still chime when you first start your engine, and the seatbelt light will stay on to remind you. The light can be deactivated also, but it is a much more complicated (and I feel unnecessary) procedure. WARNING!!!: DO NOT deactivate the seatbelt chime by cutting or splicing the wires to the seatbelt buckle under the seat. THIS WILL DISABLE YOUR AIRBAGS even if your belt is buckled!!! AIRBAGS are DEADLY if your belt is not buckled, so there is a sensor in the buckle which disables the airbags when the belt is not buckled. If you cut or splice these wires, you also disable that sensor. Turning off the chime using the programming option keeps your airbags working properly. Hope this helps, ENJOY YOUR DODGE!!! -Mike Vidal, Forked River, NJ
How do you disable seat belt alarm 2010 jeep wrangler?
Insert key into ignition ,buckel seatbelt,and turn key to on ,but do not start engine. Within 60 seconds, Unbuckel and buckel seatbelt 3 times. Cycling seatbelt indicater on and off . Red led in lower right of guage cluster will flash three times to indicate reprogram.
