answersLogoWhite

0


Best Answer

puch top of clip in and slightly to the left, it will then unclip and hinge downwards, releasing the bulb.

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you unclip the headlight retainer spring on a peugeot 307?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Is it difficult to unclip the retainer springs on the headlight bulb of a 2003 Mercedes C240?

Not at all...press in (together) and it pops off.


How does one fit a Peugeot headlight?

on the peugeot 205 the headlight can be fitted / removed as follows; lift the bonnet the headlight assembly is held in place by 2 springs on the sides unclip each spring there is a slotted grub screw above the lamp that adjusts the angle of the lamp slacken off this screw (counter clockwise) you will find that the connecting rod is fitted using a small ball joint. unclip the ball joint and the lamp will then release. the wiring connections to each bulb are a simple spade type push fit.


How do you unclip the retainer springs on the headlight bulb of a 2003 Mercedes c240?

Just look at it closely...push in, squeeze...releases Not a good answer, you smug SOB.... This is the most ill conceived POS I have ever run into,


How do you change the head light bulb on 1996 corsa?

There is a plastic cover that screws into the headlight housing turn it anti-clockwise to reveal ur h/l bulb. Remove the plug 1st then unclip the spring!


How do you replace headlight bulb magna?

unplug electrical connector remove rubber boot unclip spring and swing spring back. pull out old halogen bulb from bracket. replace with new bulb (not toching glass) swing back spring and clip to housing replace rubber boot plug in connector Test headlights...finished


How change wiper blade peugeot 306?

To change the wiper blade on a Peugeot 306 unclip the old part from the mount. Take the new wiper blade and slide it into place until it clicks.


How do you change a headlight bulb in a 91 pulsar?

you open the bonnet and then you go to the back of the headlight and youll see a wire and clip attached to the black casing unclip that wire and then unscrew the black plastic screw then youl have a clip unclip it and then pull out your light bulb and then put a new one in and put the clip back on and


How do you replace the low beam headlight located on a 2002 Kia Spectra?

Inside the engine compartment, unscrew the plasic cap over the back of the headlight, then unclip the bulb. After you pull out the bulb the plug just pulls from the bulb.


How do you change the headlight on Mitsubishi outlander 2006?

unclip H1 connector, it's really on there I needed a pry tool. pull off dust cover (rubber grommet) there will be a spring clip holding the bulb in. push in, push to the side and release. bulb will come out when spring clip is removed. depending on the bulb that's going back in, it might be better to pull the bumper off.


Replace front grill Colorado?

Open the hood. Remove the top bolts holding the grille to the radiator support. Squeeze the 4 retainer clips together to release them from the radiator support and pull the grille forward towards the front of the vehicle.. Unclip the headlight and parking light wiring from their holders while holding the grille. Reverse the procedure to install or replace the grille.. Done


How do you change a headlight assembly on a 2002 Chevy impala?

Open the hood & look for two white sliding clips. Pull them up to remove them. The headlight assembly should easily pull out. Identify the wiring harness & unclip it. Reverse the procedure to reinstall


How do you open the plastic headlight cover on a Hyundai Santa Fe?

There are two bolts on top of the headlight assembly and one on the side. Remove them and the whole headlight unit pops out. There are two cable attached. They just unclip. One side of each cable has a side you push in to release the cable. They are different sizes so you don't have to worry about which is which when you put them back in. The big black knob in the back of the unit unscrews and you are now in to the headlight assembly. Take a digital picture of the spring assembly that holds the bulb in place, so you put it back the same way. That's it! Hope it helps.