0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you convert 120 volts electric fan to 240 volt?
put double power batteries in
Can you use 240 volts with a 120 volt supply?
Only if the cable going to your well pump is a three wire. The third wire could carry the neutral and you will have 120 volts from either 240 leg to the neutral.
Can a 125 volt cable power a 120 volt piece of equipment?
The first thing we have to do is clarify the question. A cable rating of 125 volts is an insulation rating of the wire. Like wire with ratings of 300 volts, 600 volts and 1000 volts these are the highest allowable voltages that can be applied. A wire that is rated for 300 volts is good for 120 volts, 240 volts and 277 volts. At test research facilities, equipment is tested to destruction. The label that is given to wire as a result of the tests is the highest safest voltages that can be applied to that particular wire. So when you see a wire that has a label stating that it is rated for 300 volts it means that any voltage under and up to 300 volts is safe to apply. So to answer the question yes, the 125 volt insulation rating on the cable can be used to supply a source of 120 volts to a 120 volt rated piece of equipment.
Can a car battery light a bulb?
Most car batteries are 12 volts. They can light 12 volt bulbs. The bulbs in your house are likely 120 volt bulbs. A car battery will not light those without some very special equipment, or unless you were to wire ten car batteries in series.
Does 240 volt have a neutral wire?
Yes <<>> In North America, a three wire 120/240 volt system uses a neutral wire. For 240 volts two "hot" wires are used with no neutral.
If there are a red wire a black wire and a bare wire in a 120 volt supply wire which is the hot wire?
Where there is a red wire involved that usually indicates some type of special switching arrangement or more likely a 240 Volt circuit. In this case there will be 240 volts across the red and black and they will both be hot. Normally for 120 Volts the black is hot, the white is common and the bare wire is ground.
How will a 3 phase panel give you 110 volts and 220 volts?
A three phase panel will not give you 110 and 220 volts. A three phase four wire panel will, but not at these voltages. The nearest voltages will be 120 and 208 volts. The 120 volt is the wye voltage of 208 volts. 208/1.73 = 120 volts. A single phase three wire panel will give you 110 and 220 volts.
How do you wire 347 volts ballast to 110 volt feed?
You don't. A ballast with a 347 volt input is a commercial ballast. The 347 volts comes from a 600 volt three phase four wire Y system. You can change the ballast out to a 120 volt and rewire the unit but in most cases it is cheaper to buy a completely new lighting fixture.
Why is it that the outlet shows 209 volts instead of 120 volts?
Because it is a 220 volt outlet instead of a 120 volt outlet. Now, if this is a standard 120 volt outlet that is reading 209 volts then someone has made a mistake in the wiring. You need to call an electrician to straighten this out.
How do you change a 220 240 volt wire to a 110 120 volt wire?
Wire is wire - is doesn't matter what voltage you use. However, if you are changing the voltage on a device from 240 to 120, given the same power requirement, you may need bigger wires for the doubled current (and increased heat of resistivity).
Can a 10-2 wire be connected to a 10-3 recepticle for a dryer?
No, the dryer needs 120 volts supplied by the neutral third wire, along with the 240 volts for the dryer element. One of the two 240 volt supply conductors is used with the neutral to supply 120 volts to the controls and the drum motor. That is why a three wire cable is needed.
How do you get 110 volts from a 24 volt battery?
Five 24 v batteries in series give 120 v. The batteries must be the same type and all charged properly before bein connected.
