0
in a single line diagram it looks like this ( ____/ ___ ) while regular circuit breaker looks like this ____/ ____ the difference is that the first one can be removed from its place if maintenance is needed, while the regular one you can't. Viva Palestine
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What does a circuit breaker look like for 110 volt?
Most of the breakers in a panel will be 120 VAC. Double height breakers are 240 VAC. A triple height breaker probably indicates you have 3-phase power in the panel.
How do you find fuse capacity in house lightning?
To find the circuit's capacity you have to look at the breaker or fuse that protects that circuit. On the handle of the breaker you will see a number. that number is the tripping capacity of that particular breaker. On a glass screw in fuse you will see a coloured disk with a number on it that is the capacity that the fuse can handle before opening the circuit. On cartridge fuses the voltage and amperage rating will be printed on the body of the fuse.
What is 4 pole circuit breaker?
I have never seen a four pole circuit breaker. Breakers are single, two and three pole. Single pole for 120 volts, two pole for 240 volts and three pole for three phase loads. In North America all neutrals are SN (solid neutrals) and are not switched. In certain applications using a three phase Y-connected load, where complete isolation of the load from the supply is required, the neutral line connects to one pole of a 4 pole circuit breaker.
Why does your motorcycle circuit breaker pop when you hit the brake?
Check the wire that goes to your break light. Somewhere along the circuit it is grounded before the lamp and after the switch. Look on the circuit from the switch to the lamp. What is happening is, the circuit is good up to the time that you apply the break. This closes that brake light switch, When the switch closes it sees the dead short and not the lamp. The breaker popping is protecting the circuit wiring from burning up.
Why does the breaker trip after changing a receptacle?
I do not even know that it is the light switch that is popping your circuit breaker! It may be the switch or something else. The light switch controls a circuit. As electricity passes through that circuit it is heating up a contact or a weak place in a wire. At a certain point that hot place in a connector or in a wire allows the electricity to jump out of the circuit and not go through the light. When that happens, the circuit breaker pops. You can turn off the circuit breaker. Then you can look at the connectors on your light switch. If one of them looks burned, You have solved the problem. You replace the light switch. Next comes the more difficult task of looking at the connectors for your lamp. If they are not easy to get to, you call an electrician.
What procedure should be followed when a circuit breaker trips?
Look for the cause of the trip and correct. Reset the circuit breaker. If it continues to trip it might be an overloaded circuit, loose connections in the circuit, or a short in the wiring somewhere.
How do you reset the circuit breaker on the cigarette lighter on a 63 ford falcon?
It does not have a circuit breaker. It uses a fuse to protect the circuit. Look for a blown fuse in the fuse panel under the dash on the drivers side.I believe the cigarette lighter circuit is protected with a glass barrel fuse not a circuit breaker. Check the fuse box for a blown fuse.
What is the proper ampere rating of circuit breaker for electric arc welder?
The proper ampere rating of a circuit breaker for an electric arc welder depends on the arc welder. Each is different. Look at the nameplate on the arc welder and choose the circuit breaker and wiring accordingly.
Do you have a 15 0r 20 amp circuit?
Go to your distribution panel and shut off the breaker that you think is the circuit in question. If the circuit becomes de-energized then the breaker you just turned off feeds that circuit. Look on the handle of the breaker and the number you see is the amperage of that circuit. <<>> Determination of a 15 or 20 Ampere circuit is normally indicated by a combination of a 20A breaker and a 20A dedicated outlet. A 15A circuit normally has multiple outlets; not typical in a 20A circuit.
What does a circuit breaker look like for 110 volt?
Most of the breakers in a panel will be 120 VAC. Double height breakers are 240 VAC. A triple height breaker probably indicates you have 3-phase power in the panel.
What happens when the circuit is complete and the switches are closed?
*Look at the simple circuit illustrated in Figure A-2. What will happen when only switch S1 is closed? Correct Answer= "Nothing will happen-the light bulb won't light up." <<>> If there is a load in the circuit the load will operate. If there is no load in the circuit and it is complete then a short circuit will occur and something in the circuit will burn open. If the circuit is complete and there is a fuse or breaker in the circuit, then the fuse or breaker will open the circuit.
How do you find fuse capacity in house lightning?
To find the circuit's capacity you have to look at the breaker or fuse that protects that circuit. On the handle of the breaker you will see a number. that number is the tripping capacity of that particular breaker. On a glass screw in fuse you will see a coloured disk with a number on it that is the capacity that the fuse can handle before opening the circuit. On cartridge fuses the voltage and amperage rating will be printed on the body of the fuse.
Why does a new AC in a new house throw the outside circuit breaker once a week?
If the breaker only trips once a week you may have a bad breaker or the breaker may not be large enough for your A/C unit. You should also have an electrician look for any loose connections from the unit to the breaker panel. (It is not uncommon to have a bad breaker)
What is 4 pole circuit breaker?
I have never seen a four pole circuit breaker. Breakers are single, two and three pole. Single pole for 120 volts, two pole for 240 volts and three pole for three phase loads. In North America all neutrals are SN (solid neutrals) and are not switched. In certain applications using a three phase Y-connected load, where complete isolation of the load from the supply is required, the neutral line connects to one pole of a 4 pole circuit breaker.
What does a closing look like?
A closed circuit would look like a circuit which has no disconnected wire and when the current is flowing continuously
Where is the circuit breaker in 1985 BMW 535?
Look in the driver side lower dash toward the middle console. It is on your right hand.
What does a vacuum breaker look like?
That would depend on the application as there are many uses and shapes and specifications for a vacuum breaker
