0
How does fund and securities flow in primary and secondary markets?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the Difference between primary and secondary market in transaction as related to flow of fund in transaction?
What is transaction what it contains
An increase in investments in long term securities will?
decrease cash flow from investing activities
Basic requirements of an effective financial system?
The financial system is a complex mix of financial intermediaries, markets, instruments, policy markets, and regulations that interact to expedite the flow of financial capital from savings into investment.
What are three factors of production and the two types of payments that appear in the free market circular flow model?
The three factors of production are capital, labor, and land. Two types of payments are from firms and households. These payments go to the goods and services markets.
What is the best why to get start up money for a business?
We counsel entrepreneurs to prepare themselves and their businesses for entry into the capital markets, e.g., to raise money. The fundamental element of this preparation is the documentation that potential investors will review. This documentation includes a comprehensive business plan with 5 year pro formas (cash flow, P&L and balance sheet) and the full disclosure information required by the Securities Act of 1933, as amended. Yes, even a private company must comply with the laws and regulations pertaining to capital raising.
If a caterpillar is a primary consumer what level will energy flow to next after the caterpillar?
Secondary Consumer
Flow chart of 3 economic sectors?
Primary sector secondary sector tertiary sector
What is an over flow drain?
They are secondary drains that work in tandem with the primary pipes to prevent overflows.
What is the Difference between primary and secondary market in transaction as related to flow of fund in transaction?
What is transaction what it contains
Differentiate delta to delta connection of the transformer to delta to Y connection?
In delta to delta there will be no ground on both primary and secondary sides. Leave the primary side but we take care on secondary side. If there any fault occurs on the secondary then there will be unbalanced voltages between the phases results in the flow of current through the secondary windings so only we are using star on the secondary side while having neutral to prevent such a current flow.
In a transformer what induces a current in the secondary coil?
The current flowing in the primary generates a magnetic field which induces a current in the secondary winding.AnswerNo current is induced into the secondary winding of a transformer. What is induced is voltage. Current will only flow in the secondary winding if it is connected to the load, and it is the load that determines the current, not the primary current.
What is percent Z pertaining to electrical transformers?
% voltage drop on full load from the secondary to the primary due to leakage reactance and the resistance of the windings.Answer'Percentage impedance' is a confusing term. It describes the value of primary voltage that will cause the rated secondary current to flow in the short-circuited secondary winding, expressed as a percentage of the rated primary voltage.
Why the primary coil and the secondary coil of a physical transformer wrapped on each other?
Close approximation of the primary and secondary coils makes for an efficient transformer. It is the rise and fall of the magnetic field that surrounds the wire in the primary that induces a current to flow in the secondary. The closer the wire producing the magnetic field is to the conductor being cut by the magnetic field (induction) the better the secondary output.
Why should the secondary of a voltage transformer not be short circuited?
A voltage transformer takes a primary voltage and steps it down to a smaller secondary voltage. This type of transformer will attempt to keep the secondary voltage at a specific ratio of the primary voltage. If you short it, massive current flow in the secondary is required to do this. For a similar reason a CT should never be open circuited - because it attempts to push a specific ratio of primary current through the secondary. If you open circuit the secondary, it takes a massive voltage on the secondary to accomplish this.
What is impedance voltage in a transformer?
Power transformers have an impedance (Z) rating that is listed in %. So the nameplate might state 5% Z for example. What this means is that when the secondary conductors are bolted together then 5% of the rated primary voltage is applied and will generate 100% current in flow in the secondary. Example: you have a 75KVA Delta-Wye 5% Z transformer with a 480V primary rating and 208/12 secondary rating. The amp rating of the secondary is 208A [75,000/(1.732x208)] So if you applied 24VAC to the primary with the secondary bolted together with busbar then you would have 208A of current flow.
When the transformer is connected to the power source the secondary current is 0 what is the possible fault in the transformer?
A secondary current of 0 would suggest to me that the secondary circuit is open. A normally operating circuit with zero current flow would be very unusual. No load in secondary circuit. No secondary current can also be attributed to the primary power source open or an open primary winding.
How do you calculate current flow transformer when 240 Vrms is supply?
The secondary current of a transformer is determined by the load and the secondary voltage applied to that load, and this, in turn, will determine the primary current by the inverse of the turns ratio. However, if you are asking about a transformer's rated secondary and primary currents, then you need to divide the transformer's apparent power rating (expressed in volt amperes) by the rated secondary and primary voltages respectively.
