0
It depends on how powerful the motor is, and what type of load it is driving.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What size breaker for a 208 volt single phase motor that pulls 1.4 amps?
208 volts is not a common single phase voltage but you could just size your breaker to the capabilities of the conductor. 208 is normally a phase to phase voltage <<>> Many 230 volt motors can be connected to lower voltage supplies. These motors can be connected to supplies of 208 and 200 volts. The code requirement is that the 230 volt full load amperage of the motor be increased by 10% and 15% respectively for wire sizing and breaker selection. To answer the question you will need a two pole 15 amp breaker.
How does 120 volts come from 208 volts?
208 is a three phase wye connection voltage. To obtain the each individual coil voltage the 208 is divided by 1.73 which equals to 120 volts. Hence you have 3 phase 208 voltage on the phase legs and 120 volts to the wye point which is grounded. This same formula is used on any 3 phase system. 600/347, 480/277, 208/120.
How do you meter a 208v load meter only 1 phase add the two?
The voltage 208 is a three phase voltage. Single phase is classed as the voltage obtained from any two legs of the three phase voltage system. The voltage between L1 to L2 = 208. L2 to L3 = 208 volts and L3 to L1 = 208 volts. To measure the load of the 208 volt device just clamp an amp meter around one of the legs coming from the load. This will give you the amperage that the load draws.
How many Amps for 3 horsepower at 208 volts?
For a single phase 3 HP motor at 208 volts the amperage is 18.7 amps. For a three phase 3 HP motor at 208 volts the amperage is 10.5 amps. This figure is derived at by taking the full load amps at 230 volts and adding 10%. As the voltage goes down the amperage goes up. For 200 volt motors 15% is added to the FLA of a 230 volt motor.
Will 220 volt work in a high volt 3 phase motor?
Yes a 208 voltage motor will operate on 220 volts. You have to increase the motor overload protection by 10% of the motor's full load amperage to protect the motor.
How many amps does 30KW strip heater draw at 208 volts 3PH?
Assuming it is a 208-volt line voltage (as normal in 3-phase) the phase voltage is that divided by sqrt(3), or 120 volts. Each phase has to supply 10 kW so the current on each phase is 83.3 amps.
Can you use 600VOLT motor in 220VOLT supply through a transformer?
Usually with a voltage of 600 volts the motor will be three phase. To use a transformer with that motor you will need a three phase 240 volt service. These days utility companies are moving away from three phase 240 and substituting it with 120/208. The 208 three phase service has the added bonus that 120 volts can be obtained from the star point (grounded neutral).
What voltage should 208 3 phase leads read?
From line-to-line (any two of the three leads) voltage or 'line voltage', the voltage is 208 V. The line-to-neutral (one of the three leads and the neutral conductor), or 'phase voltage', is 120 V.
You have three phase power and you have a motor that needs 208 volts can you conectt it to the line carries 208 only?
If your appliance or motor is asking for 208 volt, it usually means that it also wants 3 phase. If you measure the voltage between the hots on a 3 phase feed, you will find that it is somewhere around 208v. As long as you connect it to the 2 or 3 hots that you measured, then you will be fine. Make sure you ground, and no neutral should be present.
In a 3 phase 480 panel what voltage should you get phase to phase?
The voltage you are referring to is a 'line-to-line' voltage ('line voltage'), as there is no such thing as a 'phase-to-phase' voltage.480 volts. In real life, the voltage will vary slightly by up to 3% (14 V) on a properly sized circuit. Line to neutral will measure 277 volts, plus or minus 3%.
How is it possible that a chicken rotisserie that uses 208v 3 phase can have a motor that uses 208v?
Two scenarios are that the motor could be a three phase motor. These three phase motors are manufactured in smaller sizes. The other scenario is that the motor is a 208/220 volt single phase motor. It will operate on 208 volts by taking two legs of the three phase supply for its operation.
How can change voltage from 440 v 3 phase to 208 v 3 phase?
I have 12 amps 208/3/60 what would the amps be @ 440/3
