It would be at least 250 amps, maybe 300 amps.
It is drawing .06 amps.
23
Minimal 100. Depends on load draw of home. Can be 200 amps or 400 amps as well.
Watts = Volts times Amps. Therefore, if the voltage was 220 volts, the motor would draw 500 amps. If the voltage was 4,000 volts, the motor would draw 27.5 amps. The voltages for large powerful motors tend to be relatively high, for example in the 380 Volts to 11,500 Volts range.
Each baseboard heater will draw a little over 4 amps at 120 volts or 2 Amps at 240 volts. The total number of baseboards on a circuit will draw the sum of these amps. Keep the load under 80% of the amperage rating of the breaker.
3000w / 220volts = 13.63amps 3000w/ 110volts = 27.27amps
it draws 210 amps
Power (P), in Watts, is equal to the Voltage (V), in Volts, multiplied by the Current (I), in Amperes. P=V*I Using Algebra to solve for the Current (Amps) that are required: I=P/V Therefore: 2000 Watts / 12 Volts = ~167 Amps Please note, that this is for a 100% efficient inverter. If the inverter is 90% efficient the actual draw would be: Iideal*(1+(1-(%Efficiency/100)))=Iactual 167 Amps*(1+(1-(90/100)))=Iactual 167 A * (1+(1-0.9))=Iactual 167 A * (1+(0.1))=Iactual 167 A * (1.1)=Iactual 183 A = Iactual The continuous current draw for a 90% efficient power inverter, operating from a 12V DC source, out putting 2000W at 120V AC, is 183 Amps.
Answer If, when you state "...240 watt 2.0amp..." you are indicating that 2 amps, or 240 watts at 120 volts, then that inverter will power a device which does NOT draw more than that amount of current. Check the plate or label on the compact fridge you want to power, and find the maximum current draw. For appliances, it will usually be stated in amps, rather than watts. If that amount is equal to or less than the output of your inverter, then it should work. Also, pay attention to the maximum current used by the appliance, versus the continuous output figure for the inverter, NOT the peak momentary output.
amps like.. amplifiers? it depends on how many speakers you have. or amps like.. current draw? again. depends on your power needs, your power amps... ect
Maybe, or maybe not. Depends upon the wattage or amperage draw. At 120 volts and 150 watts, you can draw about 1.2 amps. Probably not enough for a newer laptop, but may power an older one fine. A 300 or 600 watt inverter can be bought on eBay for about 30 bucks.
The electric heater will have power rated in Watts. The Amps it will draw depends on the voltage system you are using. Can be calculated by formula I (Amps) = P / V In the USA with 110V system a 2400W heater will draw 2400 Watts / 110 Volts = 21.8 Amps In Australia with a 230 V system a 2400W heater will draw 2400 Watts / 230 Volts = 10.4 Amps
It all depends upon what is "ON" at the time. A running vehicle with only the ignition system operating uses about 10-15 amps. Turn on the headlights and it will draw an additional 10 amps. With everything on, it can draw from 30-100 amps. Do you mean "what is the alternator rated at?" Your Jeep alternator would be normally rated at about 100 amps output.
You will need a battery charger capable of providing up to75 amps at 12 volts DC. This is called a converter, not an inverter. An inverter takes 12 v and transforms it usually to 120v AC or 220v Ac. Keep in mind that your 1000 watt amp will not draw 100 amps only briefly at times if at all unless you are at maximum volume. You probably could get by with a 50 amp charger and a big capacitor to supply the boost for a few seconds.
Need to know the running amp draw. Starting amps would be useful l too. The average amp draw for a simple 1hp motor is about 7 amps, such as a fan motor. Ohms law says amps times voltage = watts, so 7 amp times 120v=840 watts. Consider that starting amperage is about 1-1/2 times running load, starting watts would be about 1200. You would need about a 1200 watt inverter to run that motor.
It depends on the draw of the compressor.
draw 0.104 amps