0
How many bolts do you have to remove to change a shock on Hyundai elantra 2002?
Wiki User
∙ 13y ago
Shock Removal and Installation-
- Support the vehicle under the lower control arm.
Remove or disconnect the following:
Rear wheel
Upper shock absorber upper nut
Lower shock absorber nut
Shock absorber
To install:
Install or connect the following:
Shock absorber. Tighten the upper nut to 15-22 ft. lbs. (20-30 Nm)
Tighten the lower nut to 104-118 ft. lbs. (140-160 Nm) on 2001-03 models or 88-103 ft. lbs. (120-140 Nm) on 2004 models.
Rear wheel.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is the torque setting for a 2001 Hyundai Elantra oil pan bolts?
The 2001 Hyundai Elantra oil pan bolts torque should be 84-108 in-lbs
Where is the starter located on a 2000 Hyundai Elantra?
The starter on a 2000 Hyundai Elantra is located along the bottom, left side of the engine. It bolts directly to the engine block and is protected by a shroud.
How do you remove the back seat on 98 Hyundai Elantra?
* On fixed seats remove the bolts at base of the seat back sidecushions and detach them.Remove the two bolts at the rear of the seat cushion and detach the cushion assembly.Remove the two bolts at the base and remove the seat back * On folding seats remove the two bolts at the front of the seat cushions and detach the cushion assembly.Fold the seat backs forward remove the bolts and lift the assembly out
How do you change the starter on an 1996 Hyundai Elantra?
# Disconnect the negative battery cable # Remove the air intake duct and the air cleaner assembly # Disconnect the speedometer cable from the transaxle # Unscrew the nut and disconnect the battery cable from the starter motor then disconnect the wiring from the solenoid # Remove the starter motor mounting bolts,supporting the starter motor as the bolts are removed and remove the starter motor
How do you replace motor mounts on a 97 Hyundai Elantra?
1.Raise the vehicle and support it securly on jackstands.Support the engine 2.Remove the mount and bracket bolts and detach the mount and bracket.
How do you change spark plug wires on a 1999 Hyundai Elantra?
use a 10mm socket to remove all the bolts on the plastic cover on top of the engine. be careful, there are probably some on the left side(when you're facing the engine) as well as the top. after that, pretty simple
What is the head torque on a 2001 Hyundai elantra?
10mm bolts torque to 18 Ft-lbs 12mm bolts torque to 22 Ft-lbs
How do you take the back seat out of a 2000 Hyundai Elantra?
On fixed seats remove the bolts at base of the seat back side cushions and detach them.Removethe two bolts at the rear of the seat cushion and detach the coushin assembly.Remove the two bolts at the base and remove the seat backs. On foldingseats remove the two bolts at the front of the seat cushions and detach the cushion assembly.Fold the seat backs forward,remove the bolts and lift the assembly out.
Where are the MAP sensors located on a 2002 Hyundai Elantra?
on top of the intake held on by two 10 mill bolts
How do you go about changing the rear wiper motor on a Hyundai Elantra wagon?
Remove the inside panel from your Hyundai rear door. The wiper motor mechanism will be visible. Remove the wiper motor linkage. Remove the wiper motor wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new rear wiper motor.
How do you remove the back seat in a 2002 Hyundai accent?
To remove the 2002 Hyundai accent rear seats find the tabs that cover the bolts and unbolt them. After the bolts are out lift the seat to remove it from the car.
Got all the bolts out of a 2000 Hyundai elantra transmission but still cant get it to pry off what do you do?
you probably need to remove the bolts in the converter inside the trans, it is tricky there is only one way to get them out and you have to physicly turn the converter each time you remove one bolt at a time, sorry good luck!
