0
0, but your power source will be drained rapidly, one should be the minimum, but there are a lot of x factors I can not account for
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What amp would be best for a 12 inch 2 ohm kicker L7?
Well a Kicker ZX750.1 would work you would need 2 of them. A1000/2 - Precision Power PPI 2 Ch 1000 Watt Amplifier. HCCA-D600 - Orion 1 Ch 600 Watt Amplifier need 2. HD750/1 - JL Audio 1 Channel 750 Watt HD Amplifier also need 2
How do coupling capacitors effect the frequency response of c e amplifier?
coupling capacitors are generally used to couple the the AC component of voltage to the DC component(biased voltage) of the transistor amplifier . As we know that the capacitor itself has some reactance which is variable with the applied frequency Rc=1/wc where w=frequency in radians = 2*pi*f and f= frequency of circuit. and, V=VC+VIN VC= voltage drop on capacitor VIN= resultant voltage available for the transistor for amplification so as, frequency increases reactance decreases drop on C decreases so, voltage available for transistor increases and now you can analyse yourself for the case if frequency decreases
What happens if amplifier is connected t a DC voltage?
It will depend on the which kind of amplifier it is ,if it is made from Op amp(Non inverting Amplifier) it will simply amplify(multiply)the signal with a factor depend on the configuration of circuit which is also known as gain of the circuit.For instance if gain is 2(dimension less) and input DC voltage is 2 Volt output would be 4 Volts. and if it an Audio or RC coupled amplifier output would be zero Hence i Wrote in the starting "It will depend on the which kind of amplifier it is"
Internal circuit components of a ceiling fan?
The most important parts of the fan are- 1. Motor (Stator and Rotor) 2. Capacitors 3. Triple Capacitors (to control the voltage entering the motor) 4. Reverse Switch
How do you wire 2 subwoofers to a mono amplifier?
You can find that answer at Crutchfields.com under support
Do i need a capacitor for 2 amps and a 10'' sub?
Probably not if the current is small like 2 amps. Capacitors are used in heavy current applications when the BASS hits hard to sustain the amperage to the amplifier for a small amount of time such as a second or less.
How many capacitors did the drums of the Atanasoff-Berry Computer contain?
Each drum of the Atanasoff-Berry Computer contained 1600 capacitors. There were 2 drums.
What amp would be best for a 12 inch 2 ohm kicker L7?
Well a Kicker ZX750.1 would work you would need 2 of them. A1000/2 - Precision Power PPI 2 Ch 1000 Watt Amplifier. HCCA-D600 - Orion 1 Ch 600 Watt Amplifier need 2. HD750/1 - JL Audio 1 Channel 750 Watt HD Amplifier also need 2
If you have a sub woofer do you need an amplifier?
There are two types of subwoofers. 1. Active subwoofers 2. Passive subwoofers An active subwoofer will have a built-in amplifier. A passive subwoofer doesn't have a built-in amplifier which will require the use of an amplifier, the use of a power source.
How many subwoofers can you connect to a 1-Channel Mono Amplifier?
2
what are the types of biological amplifier?
1.differential amplifier 2.operational amplifier 3.instrumentation amplifier 4.chopper amplifier 5.isolation amplier
How many types operational amplifier?
2. Half wave and full wave
What does an amplifier with 600 watts 2 channel means?
It could be a 2 channel stereo amplifier.
What is a difference between an operational amplifier and instrumentation amplifier and can you use one opamp to perform a same task as 3 opamp instrumentation amplifier?
An op amp is made from transistors, resistors and capacitors. It is enclosed in a "chip". A basic instrumentation amp is made of 2 op-amps. you can't have a single op-amp perform as good as a instrumentation amp, although it can perfrom the same task. An i-amp has much better CMMR (common-mode rejection) and a higher input impedance.
What brand of amplifier should be avoided for lack of quality?
Neuhaus T-2 Amplifier is not so good.
Physics numerical four capacitors each of 2micro farad are connected in such a way that the total capacitance is also 2 micro farad show what combination gives this value?
In order to connect four 2 microfarad capacitors such that the total capacitance is still 2 microfarads, connect two pairs of capacitors in series, and then connect the pairs in parallel. It does not matter, since all four capacitors are equal in value, if the center point is connected together or not.
What size capacitor you need for a 1000 watts amplifier?
It takes 1 farad for every 1000 watts so u need 2 farads.
