0
well endless unless you make it turn 50 times but because air travels threw the turns with relativity minimum restriction and the upc code book has a maximum length for each size of vent pipe and if you make it one pipe size bigger it then it has no limit of length before exiting out of a building.
Venting is based on developed length of pipe and fittings BUT unlike water, friction losses are not calculated in.
As long as the vent grades up away from the fixtures trap it serves you will not have a problem and ((where you have a possible condensate situation you may have to install a drip leg (behind) the trap of the fixture)) <-- doesn't makes sence.
Another cause for a to become ineffective is if someone who lives in a colder climate does not take hoarfrost into consideration when sizing a vent terminal as the vapor cannot flow through the pipe < no hoarfrost but snow covering the pipe.
What else can I help you with?
You have fuel oil furnace there is a fuel oil smell in house when blower turns on this is even when the ac is on in summer What and where might your problem start and what can you do to eliminate it?
Check your vent pipe. Does it vent to the outside? If so, is it blocked? Is the vent pipe breached? The vent is the most likely cause.
Where is the vent shaft in the carrot cake factory in poprtopica?
The vent shaft is near the processing room. It's the vent right before the processing room.
What is the best way to clean a lint vent with a lint vent cleaner?
To clean a lint vent with a lint vent cleaner, first unplug the dryer and disconnect the vent. Insert the lint vent cleaner into the vent and move it back and forth to remove lint buildup. Repeat as needed until the vent is clean. Reconnect the vent and plug in the dryer before using it again.
How do you unclog a vent pipe on a septic and well?
There is no single vent pipe on a septic and well. ( -Or if there is, someone has made a colossal and dangerous error. ) - If the vent on your septic is clogged, then your tank is way past it's time to be pumped out, and that MUST happen before you clean the vent.
Should the trap be before or after vent?
Depends on your perspective what is before or after. If you're following the direction of the water flow, the trap needs to be before the vent. A water filled trap blocks bad smells/dangerous gasses from entering your home. Putting the vent closest to the sink would bypasses that block. It would also likely cause gurgling because of siphon action trying to pull the water out of your trap (the vent breaks the siphon because its easier to pull air down the vent than to remove the water from the trap) Right = Sink - trap - vent - main drain stack
Where is the vent control valve on 2004 altima?
Mine just failed on my car...about to dig into the repair. Will let you know how the job turns out and where located.
Should the trap be before or after vent or condensation drain?
The trap should be before the vent. The trap is used to maintain a watter barrier to prevent waste water and sewer gasses from entering the home. The vent is use after the trap to allow the water to flow freely in the pipe with out drawing the water from the trap.
How many fan in the laptop?
One cooling fan, one intake vent and one exhaust vent.....
What are the best practices for cleaning dryer vents using dryer vent brushes?
To clean dryer vents effectively using dryer vent brushes, follow these best practices: Disconnect the dryer from the power source before cleaning. Remove the vent cover and insert the brush into the vent to dislodge lint and debris. Use a vacuum to remove loosened debris from the vent. Reattach the vent cover and plug in the dryer before use. Regularly cleaning dryer vents helps prevent fire hazards and improves dryer efficiency.
How can I clean my dryer vent without moving the dryer?
You can clean your dryer vent without moving the dryer by using a vent cleaning kit with a flexible brush or vacuum attachment. Insert the brush or attachment into the vent from the outside and remove any lint or debris. Be sure to disconnect the vent from the dryer before cleaning to prevent damage.
What is the cover of the vent?
Vent covers are manufactured in many different sizes to be able to fit all vents. The purpose of a vent cover is to protect a vent from allowing rain to enter, while still allowing air to circulate.
How many elbows can a plumbing vent have in a typical installation?
In a typical plumbing vent installation, there can be up to two elbows.
