0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Where does vibration occur most in a lathe machine?
Some major sources of lathe vibration are as follows: 1.) The stock you are turning is not centered properly, or has a lopsided mass. This has the same effect of to much clothes on one side of your wash machine during spin cycle. You can cure this by slowing down the speed you turn at until the roughed stock is more centered. 2.) Take a look at the head stock on your lathe, if it has worn bearings, if the pulleys are out of line or your belt is worn, you will most likely get vibration. 3.) Look at the floor your lathe is on. Is it solid? Cement is the best surface, an flex in your floor will result in lathe vibration. 4.) Look at the stand your lathe is on, is it solid, is it true. A level will let you know if youre base is sagging under the weight of your lathe. Make sure your lathe base is solid and not attached to surrounding walls. The common fixes: Bring your head stock and tailstock together until they touch. Do they line up perfectly, if not you may have a lathe base or floor that is sagging under the weight. Spin the lathe by hand. Is it smooth? If its rough or bumpy chances are you have worn bearings that need to be replaced. Use a straight edge to make sure all belts and pulleys are in line. Being off center will cause vibration or can cause un-even wear of the belts which in turn will cause vibration. If the belt is worn replace it. Add some weight to your base. The lathe is heavy so any vibration is sent right through your base and magnified. Add weight makes it harder for the lathe to move around and will decrease vibration of an out of round piece of stock.
Example of products made by using lathe machine?
We use the lathe machine for facing, knurling, grooving, etc... n gen we use all these processes after foundry and casting of a object... We can use lathe for threading, cutters etc.....
How much does jamb form cost?
1,000,000,000 dollars
How much does a windmill cost?
As much as it costs
How much does it cost to become a plumber?
It cost approximately $10,000
How much does a wood lathe cost?
It will cost about 85 to 200 dollars it depends on what you want on it.
How much old metal lathe worth?
The cheapest metal lathes cost around $180. More expensive models can cost up to $6,000. The smaller and less complex the lathe, the cheaper the price.
How much do front brake hoses cost?
How much should it cost for a car dealer to connect brake hose
How much does it cost to buy or replace the brake pads on a 2003 Passat?
How much does it cost to get brake pads repaired on VW 2003 Passat
A certain type of lathe costs seven times as much as a certain make of drilling machine if two such lathes and three such drilling machines cost 8500 what is the cost of each machine?
Cost of drill = x. Cost of lathe = 7x. Cost of two lathes and 3 drills = 7x + 7x + x + x + x = 17x. If 17x = 8500, then x = 500. Each drill costs 500. Each lathe costs 3500.
How much does brake pad repairs usually cost?
Repairing a brake pad will cost about $100 if done by a mechanic. If you do it yourself, it could cost about $20.
How much does it cost to replace brake pads?
If you are looking for more information on how much does it cost to replace brake pads, the best place to look for the information is on ask.metafilter.com/39783/A-reasonable-price-for-a-brake-job
How much is brake rotor replacement going to cost me?
If you are wondering how much brake rotor replacement is going to cost because your car needs a new brake rotor, then the answer is around 200-400 dollars.
How much does it cost to replace brake line on Hyundai?
The average cost to replace a brake line on a Hyundai is about 15 dollars for the part. The service and installation can cost as much as about 300 dollars at a dealership.
How much does a brake light switch cost?
20.00
How much did it cost to build the elevator brake?
$7
How much does a brake pad replacement cost.?
Brake pad replacements are cheap. Last time I paid for brake pads, it was $15 for two. It depends on your vehicle but if you have a regular Honda or Chevy then it shouldn't cost much.
