1 volt is.
Conductors allow most, if not all, electricity to pass through it. This is due to "wandering electrons" that aren't tightly bound to the nucleus of the conductor itself.Resistors conduct some, but not all electricity to pass. It somewhat resists it, hence resistors.Insulators do not allow electricity to pass through it due to the electrons being so tightly bound to the nucleus.
To answer this question, let's look at the definition of the following words. Voltage, Current, and Resistance One volt is one joule of energy per coulomb of electrons. One ampere means one coulomb of electrons is moving through the wire each second. R = V ÷ I = J/s ÷ C/s = J/C The resistance measures the amount of energy that is required to make one coulomb of electrons move through the wire. The charge of one electron is 1.6 * 10^-19 C. To determine the number of electrons per coulomb, invert this number. Number of electrons per coulomb = 6.25 * 10^18 One ampere means 6.25 * 10^18 electrons are moving through the wire and resistor each second. If the resistor is one ohm, one volt will be required for this to happen. To determine the amount of charge that is moving in a wire each second, you will need to wire's resistance and the voltage that is being used. Voltage and resistance determine the amount of charge that is moving through the wire each second. I hope this answers your question.
32v
The power to propel a ship is dependent on a number of things besides resistance. You must consider the size of the ship, its weight, and its passenger's weight before you can determine the power required to move it.
Voltage across a resistance = (resistance) x (current through the resistance) =4 x 1.4 = 5.6If the ' 1.4 ' is Amperes of current, then the required voltage is 5.6 volts.
Resistance of a material is depend on the force required to withdraw electrons from the atoms of that material.
Ok so if you have to take the 5 amperes and multuply them by the 22 ohm resistance giving you the answer of 110 5 * 22 = 110 volts
In an electrical circuit there is a flow of electrons. The flow is induced by the creation at a production station, battery, or other supply of an "Electromotive Force (E)". The size of the electromotive force is measured in "Volts". The rate of flow of the electrons through the circuit is called the "Current (I)". Current is measured in "Amperes". The typical conductor for transporting electrons through a circuit is wire and the smaller the diameter of the wire the more the "Resistance(R)" to the flow; the larger the diameter, the less the resistance. Resistance is measured in OHMS. Definitions of volt, ampere, and ohm: 1 volt: Electromotive force required to send a current of 1 ampere through a system in which the resistance measures 1 ohm. 1 ampere: Rate of flow of electrons in a system in which the electromotive force is 1 volt and the resistance, 1 ohm. 1 ohm: Resistance offered by a system in which the electromotive force is 1 volt and the current, 1 ampere.(Found at http://www.tpub.com/content/engineering/14069/css/14069_52.htm)
There is the kinetic energy you are familiar with, just moving around There is also electrical kinetic energy, the energy required to move electrons within a circuit this energy is also known as electromotive force of Voltage
There is the kinetic energy you are familiar with, just moving around There is also electrical kinetic energy, the energy required to move electrons within a circuit this energy is also known as electromotive force of Voltage
Conductors allow most, if not all, electricity to pass through it. This is due to "wandering electrons" that aren't tightly bound to the nucleus of the conductor itself.Resistors conduct some, but not all electricity to pass. It somewhat resists it, hence resistors.Insulators do not allow electricity to pass through it due to the electrons being so tightly bound to the nucleus.
The effort required would be proportional to the resistance.
required to excite the electrons of the chlorophyll and start the cyclic and non-cyclic phosphorylation?
The number of electrons are required to predict the charge of the ion.
It indicates how many electrons are required to complete a full valence shell.
Electricity is the movement of electrons between atoms. Magnetism only exists around moving electrons.
absence of friction...no air resistance