0
How much is an FIE Western Duo Cal 22 lr revolver worth The gun can be fired but you have to load it via the loading gate the pin can't be removed to take out the cylinder?
Wiki User
∙ 9y ago
$100-$150.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How do you open the cylinder on a revolver without a cylinder release?
Depends on the revolver. Some inexpensive guns had a removable cylinder pin- it would be removed, the cylinder could now be removed, and the pin used to eject empties. Older revolvers may have been "top break" guns- raising the cylinder latch permitted to barrel and cylinder to swing open on a hing, much like a double barreled shotgun opens.
Will a 22 magnum fire without gun barrel?
A rifle that has barrel removed- not likely. Revolver that has barrel removed- VERY likely.
How do you remove the firing pin from a heritage 22 revolver?
Take it to a gunsmith. Remove cylinder - remove firing pin pin located under rear site - use finishing nail/small center punch ,place against back of firing pin and tap lightly driving pin toward "removed" cylinder
How do you disassemble a smith and Wesson model MP?
A Smith and Wesson M&P model is a 6 shot revolver in 38 Smith & Wesson Special caliber. The MP or M&P stands for "military and police".To disassemble the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left.When the grips are removed the side plate will be fully visible.Remove the screws from the side plate.To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit.Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off along with the hammer block, so be sure it falls on a padded surface.At this point most internal parts will be visible and accessible.The cylinder can be removed by sliding the cylinder crane to the left and out of the frame, while holding the cylinder in place.The cylinder will now be free.To reassemble the revolver, do the above in reverse, making sure the hammer block is in place and the side plate seats correctly.You can tap on the side plate with a wood or plastic tool to seat it properly.Replace the cylinder crane and cylinder. Be sure the correct screw is used to hold the cylinder crane to the frame.Replace the remaining side plate screws in the correct place along with the grips and grip screw.Holding back the hammer slightly, or with the hammer cocked, look in the gap between the hammer and frame to be sure the hammer block has been replaced.A word of caution here: know exactly what you are doing before making alterations or repairs. Revolvers are delicate and expensive machinery.
How do you replace the slave cylinder on a 1999 S-10?
The transmission has to be removed to gain access to the clutch slave cylinder.
How do you get the bullets unloaded from an inherited Model 925 38 SW handgun that is loaded with bullets?
I think you have a Harrington and Richardson 925 in .38S&W. It is a top break revolver. KEEP YOUR FINGERS AWAY FROM THE TRIGGER WHILE YOU DO THIS. In a top break revolver, the frame is hinged at the bottom front of the cylinder. Releasing the lock, (should be at the top of the frame - might require some backward pulling to engage) and pushing the barrel down brings the cylinder up. This will exposes the rear of the cylinder. For most top break revolvers, the act of pivoting the barrel and cylinder operates an extractor that pushes the cartridges in the chambers back far enough that they will fall free, or can be removed If you can't get it to work, leave it alone and find a qualified gun smith.
How do you repair a Blown head gasket on your 1994 Buick century 4 cylinder?
The 1994 Buick Century 4 cylinder head gasket will have to be removed and replaced. The head has to be removed, along with anything that is physically in the way of removal, before the head gasket can be removed.
2 circular faces?
A cylinder, or a torus (donut) with a chunk removed.
Why does radio display in 2008 Hyundai elantra read loading?
No one seems to have a good answer for the LOADING problem. I removed the Batt. cables and the LOADING went away for a couple of days but came back. I've had it with Hyundai, they just say buy a new radio because they don't know what to do.
How do you load a standard 38sp fie Miami fl?
If you have the Standard revolver, this is a "pull pin" type action, where the cylinder pin slides out the front, and the cylinder is removed from the gun to be loaded. For further instructions, I would recommend you to your local gun shop. While you are there, ask them to examine the gun to see if it is safe to fire. These were not especially high quality firearm- the retail value of a used FIE Standard is below $100.
Where is slave cylinder on 1997 Isuzu hombre?
The slave cylinder is on the input shaft of the transmission at the throw out bearing. The transmission will have to be removed to change it.
Wheres the cylinder in the WWE HD Stage?
they removed them and added random lights
