0
How much should you torque your aluminum intake on a 454 motor?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is torque percent in electrical motor and unit of torque?
In SI, torque is measured in newton metres (N.m). The percentage torque varies according to the design and specifications of a motor.
What is the difference between max torque and breakdown torque of a electric motor?
Max torque and breakdown toarque are the same...,.the point at which a motor will stop/stall.
What is motor rated torque?
It is the twisting force that a motor can produce when it is running.
Which motor has a higher starting torque?
A series-wound commutator motor has the best starting torque because the torque is proportional to the square of the current, and the starting current is set by a current-limiting resistor which is switched out as the motor builds up speed.
How is pull out torque developed?
With some motor designs, as the motor starts to accelerate, its torque tends to fall somewhat before starting to increase again. The point of lowest torque in this region of the curve is termed the 'pull-up torque'.
1996 Chevrolet c1500 pickup truck bolt torque specifications for 5.0L intake manifold?
1996 chevy c1500 pick up 305 motor bolt torque spec intake manifold
What are the torque specifications for a 2002 Chevy Malibu 3.1 engine?
what is the torque specs to a 2002 Chevrolet Malibu 3.1 liter motor. Need head and intake torque specs. and sequence.
What house hold product can i use to clean my aluminum intake on my motor?
Simple Green mixed 50/50 with water.
Where is the iac sensor on a 99 Ford Explorer?
IUIAC motor is allways located in the upper plenun (intake) where the plastic pipe comes from your air filter to the aluminum...its either on one side or the other of where your throttle cable connects to the intake. should be round with an electrical clip.
What should each head bolt be torqued at?
Torque specs are very specific, based on whether or not the bolts are reusable, and if they are going through or into aluminum. you need to get the correct number and pattern for your motor from a repair manual or autozone.com.
What are the torque specs for a Pontiac 3.8 intake manifold?
I'm pretty sure this is that same 3800 motor that gm uses in my mom's 2001 buick Le Sabre. Her intake was the fiberglass resin plastic and the torque specs are 89 INCH pounds. Make sure you use the right tightening sequence too. 89 inch pounds is for the upper intake or Plenum. 136 inch pounds is the torque specs for the lower intake
What is the torque specs for a intake manifold on a 1998 Chevy 350 motor?
I would start at 20 ft lbs on alum. 25 on cast.
What is the torque specs for a intake manifold on a 1997 350 motor?
350 ft/pds This above answer it laughable and you will break every single bolt if you try to torque them to that figures. The correct torque on cast iron heads is 30 ft/lbs.
How do you calculate hydraulic motor torque?
how to calculate hydraulic motor torque
You would like to know the torque on the intake and heads on a 1986 Chevrolet S-10 Blazer with a 2.8 liter V6 motor?
The heads or 65 ft.lbs Intake bolts 35 ft-lbs
What is the torque sequence for a Chevy small block intake manifold?
I don't know how to post a drawing, but you should torque an intake in three stages starting with the four center bolts and then going down to each of the four corners. It's generally a circular pattern that starts in the center and works it's way out to the edges. An auto repair manual such as Motor's or Chilton's can be very helpful in this situation.
How can you find out what size motor came in your 91 s-10?
it should be on the intake of ur motor it should be either a 2.9 striaght 4 or a 4.3 v6
